Simrad GO XSE Series Operator'S Manual Download Page 50 | Manualshive

Page: 50 / 242

background image

Rock filter level

Hides rock identification on the chart beneath a given depth.
This helps you to declutter charts in areas where there are many
rocks located at depths well below your vessel's draught.

Contours depth

Determines which contours you see on the chart down to the
selected safety depth value.

Presentation type

Displays marine charting information such as symbols, colors of the
navigation chart and wording for either International or U.S.
presentation types.

Annotation

Determines what area information, such as names of locations and
notes of areas, is available to display.

Chart details

Provides you with different levels of geographical layer information.

Easy View

Magnifying feature that increases the size of chart items and text.

Ú

Note:

There is no indication on the chart showing that this

feature is active.

Chart settings

The options in the chart settings dialog depends on which chart
source is selected in the system.

50

Charts

| GO XSE/XSR Operator Manual

«
...
48
49
50
51
52
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: Yardistry Pages: 9

Brand: 1010music Pages: 2

Brand: 1010music Pages: 4

Brand: JB Systems Pages: 7

Brand: 3B SCIENTIFIC PHYSICS Pages: 36

Brand: 3A HEALTH CARE Pages: 16

Short/cut 2000 Audio Editor

Brand: 360 Systems Pages: 4

Brand: LAWO Pages: 459

Brand: earline Pages: 13

Marathon Multi600

Brand: Saeyang Pages: 21

Brand: Saab Pages: 4

Brand: S&C Pages: 11

Brand: Valcom Pages: 6

Brand: Vaisala Pages: 60

Brand: YASKAWA Pages: 81

Brand: YASKAWA Pages: 52

Brand: Petzl Pages: 15

Scanmate-B DGH 8000

Brand: DGH TECHNOLOGY Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands