Simrad GO XSE Series Operator'S Manual Download Page 7 | Manualshive

Page: 7 / 242

background image

About this manual

This manual is a reference guide for operating the unit. It assumes
that all equipment is installed and configured, and that the system
is ready to use.
Images used in this manual might not exactly match the screen on
your unit.

Important text conventions

Important text that requires special attention from the reader is
emphasized as follows:

Ú

Note:

Used to draw the reader’s attention to a comment or

some important information.

Warning:

Used when it is necessary to warn

personnel that they should proceed carefully to
prevent risk of injury and/or damage to equipment/
personnel.

Manual version

This manual is written for software version 20.2. The manual is
continually updated to match new software releases. The latest
available manual version can be downloaded from the following
website:

•

www.simrad-yachting.com

Translated manuals

Available translated versions of this manual can be found on the
following website:

•

www.simrad-yachting.com

Viewing the manual on the screen

The PDF viewer included in the unit makes it possible to read the
manuals and other PDF files on the screen.
The manuals can be read from a storage device connected to the
unit or copied to the unit’s internal memory.

Preface

| GO XSE/XSR Operator Manual

7

«
...
5
6
7
8
9
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: Rangevision Pages: 31

Brand: Parker Pages: 54

Brand: Jackco Pages: 6

Brand: NCR Pages: 20

Brand: DARAY Pages: 32

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: MacDon Pages: 74

Brand: Maico Pages: 55

Brand: Maico Pages: 38

Brand: Maico Pages: 2

Brand: MAHA Maschinenbau Haldenwang Pages: 13

Brand: Rational Pages: 16

Brand: UNI-T Pages: 4

UPO3000E Series

Brand: UNI-T Pages: 94

Brand: Underhill Pages: 12

Brand: UMS Pages: 92

Brand: ubicquia Pages: 4

Brand: KAM Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands