Simrad GO XSE Series Operator'S Manual Download Page 202

Page: 202 / 242

Connect to the internet

Used for connecting to a hotspot which has internet access.
When connected, the text changes to include Already connected.

Connect your phone/tablet

Used for connecting a phone or tablet to the MFD. Refer to

"Remote

control of the MFD"

on page 205.

Bluetooth

Enables the built-in Bluetooth functionality.

Bluetooth options

Opens the Bluetooth dialog. This dialog lists Bluetooth enabled
devices.

Note:

After pairing the device you must connect to it.

Select an item in the Paired Devices list to open the Bluetooth
device details dialog. Use it to:

•

display device details

•

connect, disconnect or remove (forget) the device from the
device list

Built-in WiFi

Select this option to enable or disable the internal WiFi.
Disabling the internal WiFi reduces the unit’s power consumption.

WiFi networks

Shows the WiFi network connection status. If the MFD is connected
to the internet (WiFi hotspot), the hotspot name (SSID) is shown.

202

Internet connection

| GO XSE/XSR Operator Manual

Summary of Contents for GO XSE Series



















































































































































































































































Search results

Summary of Contents for GO XSE Series

Reviews:

Related manuals for GO XSE Series

Brands by name

Popular brands

Simrad GO XSE Series, Operator'S Manual

Search results

Summary of Contents for GO XSE Series

Reviews:

Related manuals for GO XSE Series

Brands by name

Popular brands