Simrad GO XSE Series Operator'S Manual Download Page 45 | Manualshive

Page: 45 / 242

background image

In the following example water depth from 5 meters to 10 meters
will be shaded yellow in the chart when Depth 1 is the selected
shading in the menu.

3D exaggeration

Graphical settings that are available in 3D mode only. Exaggeration
is a multiplier applied to the drawn height of hills on land, and
troughs in water to make them look taller or deeper.

Ú

Note:

This option is grayed out if the data is not available in the

map card inserted.

Genesis Layer

The Genesis Layer displays high-resolution contours contributed by
Genesis users that have passed a quality check.
This option toggles the Genesis layer on/off on the chart image.
Available only if the C-MAP chart contains Genesis Layer data.

Charts

| GO XSE/XSR Operator Manual

45

«
...
43
44
45
46
47
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: NARGESA Pages: 33

Brand: iGuzzini Pages: 20

Brand: Labnet Pages: 2

Brand: Keiser Pages: 2

Brand: ECA Pages: 3

Brand: Nautilus Pages: 12

Growers Supply 109722

Brand: FarmTek Pages: 9

Brand: JB-Lighting Pages: 32

Brand: W&H Pages: 72

Brand: Quick Pages: 24

Brand: JDS Uniphase Pages: 144

IP Video Test Option HST-3000

Brand: JDS Uniphase Pages: 14

Brand: Mangar International Pages: 8

Brand: Malvern Instruments Pages: 30

Brand: zarges Pages: 36

Brand: Parkside Pages: 2

Brand: Park House Healthcare Pages: 12

Brand: Saadat Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands