Simrad GO XSE Series Operator'S Manual Download Page 218 | Manualshive

Page: 218 / 242

background image

Simulator

About

The simulation feature lets you see how the unit works without
being connected to sensors or other devices.
The status bar indicates if the simulator is toggled on.

Retail mode

In this mode a retail demonstration for the selected region is shown.
If you operate the unit when retail mode is running, the
demonstration pauses.
After a time-out period, retail mode resumes.

Ú

Note:

Retail mode is designed for retail/showroom

demonstrations.

Simulator source files

You can select which data files that are used by the simulator. It can
be either pre-recorded data files included in your device, your own
recorded log files, or log files on a mass storage device connected
to the unit.

27

218

Simulator

| GO XSE/XSR Operator Manual

«
...
216
217
218
219
220
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: Rabe Pages: 65

Brand: Vahle Pages: 96

Brand: Xo Pages: 59

Brand: Falcon Pages: 8

Brand: IBS Scherer Pages: 64

Brand: Landoll Pages: 70

Brand: Landice Pages: 19

Brand: Landice Pages: 7

Brand: NatureZap Pages: 2

ProFire Lightbridge

Brand: M-Audio Pages: 8

Brand: M-Audio Pages: 36

Brand: Tactile Medical Pages: 23

Brand: Taarup Pages: 72

Brand: Y.I.C. TECHNOLOGIES Pages: 6

TOTAL KNEE 1900

Brand: Össur Pages: 58

Brand: Össur Pages: 50

Brand: Össur Pages: 13

PRO-FLEX XC PXC0xyyz

Brand: Össur Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands