Simrad GO XSE Series Operator'S Manual Download Page 102 | Manualshive

Page: 102 / 242

background image

In NAV mode the autopilot automatically steers the vessel to a
specific waypoint location, or along a pre-defined route. Position
information is used to change the course to steer to keep the vessel
on the track line to the destination waypoint.

Ú

Note:

For information about navigation, refer to

NAV mode options

While in NAV mode the following buttons are available in the
autopilot controller:

Restart

Restarts the navigation from the vessel’s current position.

Skip

Skips the active waypoint and steers towards the next waypoint.
This option is only available when navigating a route with more
than one waypoint between the vessel position and the end of the
route.

Cancel

Cancels active navigation and deselects the current route or
waypoint navigation. The autopilot is switched to heading hold
mode, steering the vessel on the heading that was active when the
cancel button was selected.

Ú

Note:

This is different from selecting standby which does not

stop current navigation.

Turning in NAV mode

When the vessel reaches a waypoint, the autopilot will give an
audible warning and display a dialog with the new course
information.
There is a limit for the allowed automatic course change to next
waypoint in a route:

•

If the required course change to the next waypoint is less than
the course change limit, the autopilot will automatically change
the course

•

If the required course change to next waypoint is more than the
set limit, you are prompted to verify that the upcoming course

102

Outboard autopilot

| GO XSE/XSR Operator Manual

«
...
100
101
102
103
104
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: Keithley Pages: 149

Brand: Makita Pages: 60

Brand: JB-Lighting Pages: 60

Brand: VeEX Pages: 2

Brand: JB-Lighting Pages: 48

Brand: Garmin Pages: 12

Brand: Garmin Pages: 13

Brand: H&S Pages: 42

Brand: National Instruments Pages: 10

Brand: Nautilus Pages: 17

Brand: National Instruments Pages: 6

Brand: Vibration Research Corporation Pages: 333

Wallach UltraFreeze

Brand: Cooper Surgical Pages: 4

Brand: Cuisinart Pages: 159

DJ Laptop stand +tray

Brand: Power Dynamics Pages: 3

Brand: Exmark Pages: 40

1C63 Triton Low Profile

Brand: Otto Bock Pages: 196

Brand: GARDASOFT Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands