Simrad GO XSE Series Operator'S Manual Download Page 111 | Manualshive

Page: 111 / 242

background image

Adjusting the radar range

The radar range is shown in the system information area on the
radar image.
Use the zoom buttons to increase or decrease the range.

Dual range

Ú

Note:

Halo 20 does not support dual range.

When connected to a Halo radar (other than Halo 20), it is possible
to run the radar in Dual Range mode.
The radar appears in the radar sources menu as two virtual radar
sources A and B. Range and radar controls for each virtual radar
source are fully independent and the source can be selected for a
particular chart or radar panel in the same manner as dual radar
described in

"Selecting the radar source"

Ú

Note:

Some controls that are related to physical properties of

the radar itself are not independent of source. These are Fast
Scan, Antenna Height, Sector Blanking and Bearing alignment.

The number of targets that can be tracked for each virtual radar
source depends on your radar source.
Up to two independent target tracking zones may be defined for
each virtual radar source.

Sector blanking

Radar installed in close proximity to a mast or structure could cause
unwanted reflections or interference to appear on the radar image.
Use the sector blanking feature to stop the radar from transmitting
on up to four sectors in the image.
The sector blanking option is available in the radar installation
dialog. Refer to the installation manual.

Ú

Note:

Sectors are setup relative to the heading line of the radar.

The bearing of the sector is measured from the center line of
the sector.

Ú

Note:

Sector blanking should be applied very carefully to avoid

reducing the radar’s usefulness in identifying valid and
potentially dangerous targets.

Radar

| GO XSE/XSR Operator Manual

111

«
...
109
110
111
112
113
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: Daga Pages: 24

Brand: DAF Pages: 68

Brand: Echo Pages: 6

Pro Attachment Series

Brand: Echo Pages: 28

Brand: Echo Pages: 2

Pro Vantage 12+ Series

Brand: Ecco Pages: 6

Brand: ParaBody Pages: 3

Brand: Valiani Pages: 66

Brand: Malekko Pages: 2

Brand: Major Pages: 26

Brand: KCI Pages: 2

Brand: KCI Pages: 60

Brand: Landoll Pages: 38

Brand: Wacker Neuson Pages: 34

Brand: JBL Pages: 17

Brand: popular Pages: 27

Brand: Beurer Pages: 21

Brand: SCHUNK Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands