Simrad GO XSE Series Operator'S Manual Download Page 25 | Manualshive

Page: 25 / 242

background image

Locking the touchscreen

You can temporarily lock the touchscreen to prevent accidental
operation of the system.
You lock the touchscreen from the System Controls dialog.
You remove the lock function by pressing and holding the power
key.

Instrument bar

Toggles the Instrument bar on/off for the current page only.

Connect and register

Guides you how to connect your mobile device (phone or tablet) to
the unit and register your device.

Screen capture

You enable/disable the screen capture option in the system settings
dialog.
To take a screen capture:

•

Tap the status bar or the dialog title

Screen captures are saved to internal memory.

Basic operation

| GO XSE/XSR Operator Manual

25

«
...
23
24
25
26
27
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: Waterwise Pages: 12

Brand: ParaBody Pages: 38

Brand: Makita Pages: 17

Brand: Makita Pages: 13

Brand: Parker Pages: 5

Brand: Bacharach Pages: 31

Brand: Bacharach Pages: 2

Brand: CAMAG Pages: 40

Brand: Danelec Pages: 67

Brand: Eaton Pages: 16

Brand: Eaton Pages: 6

Brand: Ecco Pages: 17

Brand: M-system Pages: 2

Brand: Rico Pages: 34

Brand: Rane Pages: 38

Brand: Kartsana Pages: 36

Brand: Malekko Pages: 2

Brand: Major Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands