manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

The Simrad GO XSE Series offers exceptional navigational capabilities and advanced features. Ensure seamless installation with the comprehensive "Installation Manual" available for "free download" at manualshive.com. This detailed "manual" provides step-by-step instructions for setting up your device, optimizing your experience on the water.

Share
Download
background image

Icon

Description

Pan to position a chart or sonar image on the
panel.

Pinch to zoom out on the chart or on an image.

Ú

Note: 

Not available for zooming sonar images.

Spread to zoom in on the chart or on an image.

Ú

Note: 

Not available for zooming sonar images.

Status bar icon definitions

Depending on your system and set up, the following icons can
appear on the status bar:

Icon

Definition

Alarm - a standard (yellow), important (orange) or
critical (red) alarm is sent. To remove the icon in the
status bar, acknowledge the alarm in the Alarms
dialog. If needed, change the alarm setting or
remedy the situation so the same alarm is not resent
immediately by the system.

Autopilot modes: Auto-Heading hold, Follow up,
Navigation, No drift, Standby. Use the autopilot
controller to select an autopilot mode.

Appendix

 | GO XSE/XSR Operator Manual

237

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Abicor Binzel FES-200 W3 Short Instruction preview
FES-200 W3
Brand: Abicor Binzel Pages: 92
Bacharach Fyrite Tech 50 Operating And Maintenance Instructions Manual preview
Fyrite Tech 50
Brand: Bacharach Pages: 48
Labelmate UCAT-S User Manual preview
UCAT-S
Brand: Labelmate Pages: 61
Labconco FreeZone Plus User Manual preview
FreeZone Plus
Brand: Labconco Pages: 62
National Instruments NI 9264 Getting Started preview
NI 9264
Brand: National Instruments Pages: 10
Easylife KMS005M Instruction Manual preview
KMS005M
Brand: Easylife Pages: 3
York FC8T-UH Manual preview
FC8T-UH
Brand: York Pages: 32
B. Braun Aesculap S4 Cervical Instructions For Use/Technical Description preview
Aesculap S4 Cervical
Brand: B. Braun Pages: 43
Enabling Technologies Dynamique Biski Owner'S Manual preview
Dynamique Biski
Brand: Enabling Technologies Pages: 44
GOZONE GZE-2201 Manual preview
GZE-2201
Brand: GOZONE Pages: 11
Tatu Marchesan RC2 2600 CL Operator'S Manual preview
RC2 2600 CL
Brand: Tatu Marchesan Pages: 52
Lightolier RT6-2 Specification Sheet preview
RT6-2
Brand: Lightolier Pages: 2
orfit Classic Stiff Instructions For Use preview
Classic Stiff
Brand: orfit Pages: 3
Game Winner HU2220401-GW Assembly Instructions Manual preview
HU2220401-GW
Brand: Game Winner Pages: 25
Karma LED PAR27 Instruction Manual preview
LED PAR27
Brand: Karma Pages: 12
p-light Hydro 880 Installation And Instructions For Use preview
Hydro 880
Brand: p-light Pages: 28
Cardin Elettronica RCQ486W00 Manual preview
RCQ486W00
Brand: Cardin Elettronica Pages: 56
Hammer Strength OHDTT Assembly Instructions preview
OHDTT
Brand: Hammer Strength Pages: 4

Brands by name

Popular brands

Load more brands