Simrad GO XSE Series Operator'S Manual Download Page 222 | Manualshive

Page: 222 / 242

background image

Ú

Note:

Do not add software update files to a chart card.

Ú

Note:

Do not turn off the unit or a remote device until the

update is completed, or until you are prompted to restart the
unit.

You will be notified if new software updates are available. You can
also manually start the update(s) from the Updates dialog.

Update the software from a storage device

You can download the software update from www.simrad-
yachting.com.
Transfer the update file(s) to a compatible storage device, and then
insert the storage device in the unit.

Ú

Note:

Do not add software update files to a chart card.

To update this unit only:

•

restart the unit to start the update from the storage device

To update this unit or a connected device:

•

Select the update file in the dialog

Ú

Note:

Do not turn off the unit or a connected device until the

update is completed, or until you are prompted to restart the
unit.

222

Maintenance

| GO XSE/XSR Operator Manual

«
...
220
221
222
223
224
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: Daavlin Pages: 13

Brand: Daavlin Pages: 27

D-IMager EKL3104

Brand: Panasonic Pages: 13

Brand: Labokey Pages: 5

Brand: E-Z Trail Pages: 8

Brand: B&K Pages: 10

Brand: Radarcan Pages: 40

Brand: Nautilus Pages: 12

Brand: CAIRE Pages: 16

Brand: Cadex Pages: 300

Brand: Wahl Pages: 2

Brand: LANGER EMV-Technik Pages: 25

Electric Clamshell CSE12-208VCD

Brand: Lang Pages: 16

Brillion 3631-25

Brand: Landoll Pages: 138

Brand: PAT Pages: 44

Brand: Park Tool Pages: 4

Brand: Qlight Pages: 4

Brand: R&S Pages: 371

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands