Simrad GO XSE Series Operator'S Manual Download Page 126 | Manualshive

Page: 126 / 242

background image

VelocityTrack

Ú

Note:

When VelocityTrack is enabled antenna rotation speed

may be reduced.

Ú

Note:

When operating the radar in Dual range mode with one

of the ranges set to 36 nm or more, increased VelocityTrack
coloring noise over land areas may be seen.

Doppler coloring is a navigation aid to distinguish moving targets
approaching or diverging from your vessel. The radar indicates if a
target is approaching or diverging from your vessel when both
these conditions are true:

•

The target's relative speed is greater than the VelocityTrack speed
threshold.

•

The target is not geo-stationary (e.g. land or a marker buoy).

The following options are available:

•

Off - turns off Doppler coloring

•

Normal - approaching targets and diverging targets are colored.

•

Approaching targets - only approaching targets are colored

The color of approaching and diverging targets depends on the
palette used:
Radar image palettes

•

Diverging targets are blue colored on all radar image palettes.

•

Approaching target colors on radar image palettes:

- Black/Red palette - Yellow
- White/Red palette - Yellow
- Black/Green palette - Red
- Black/Yellow palette - Red

Radar overlay palettes on charts

•

Diverging targets are dark grey.

•

Approaching targets are yellow.

VelocityTrack settings

Use this dialog to set speed thresholds of targets to be colored.
The speed threshold can be defined to apply for the radar source of
the selected radar panel only, or to all radar sources connected to
the system. The setting is only applied to those radars powered and
connected at the time the setting is made. If the all radar sources

126

Radar

| GO XSE/XSR Operator Manual

«
...
124
125
126
127
128
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: ZOLL Pages: 84

Brand: Kaivac Pages: 29

Brand: MacDon Pages: 65

Brand: Parker Pages: 54

Brand: Raymarine Pages: 90

Brand: Datalogic Pages: 20

Brand: Datalogic Pages: 188

Pressure Governor

Brand: Waterous Pages: 53

Brand: Landi Renzo Pages: 16

Brand: IBM Pages: 163

Brand: Jet Pages: 12

Brand: Rainin Instrument Pages: 16

Brand: JBSYSTEMS Light Pages: 17

Brand: Labnet Pages: 12

Brand: Yamaha Pages: 126

DM 2000 Version 2

Brand: Yamaha Pages: 8

Brand: Yamaha Pages: 39

Brand: Yamaha Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands