Simrad GO XSE Series Operator'S Manual Download Page 28 | Manualshive

Page: 28 / 242

background image

Adding new favorite pages

Use the add icon in the home page panel to add a favorite page. In
the Page Editor dialog, drag-and-drop the panels you want included
in the favorite page.

Edit favorite pages

Select the edit button in the favorite panel and then:

•

Select the X icon on a favorite button to remove the page

•

Select the tool icon on a favorite button to display the page
editor dialog

Customizing the instrument bar

Ú

Note:

You must activate the instrument bar in the application

to access the instrument bar menu.

28

Customizing your system

| GO XSE/XSR Operator

Manual

«
...
26
27
28
29
30
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

AJSPD850P - P2 DECK

Brand: Panasonic Pages: 73

Brand: Baileigh Industrial Pages: 40

Brand: Zenbooth Pages: 60

Brand: Raven Pages: 17

Brand: Campbell Pages: 12

Brand: Gaspardo Pages: 196

Brand: RAB Pages: 2

ThermoTweez Handpiece TT-65

Brand: Pace Pages: 14

Brand: ubbink Pages: 30

Brand: Posture Pump Pages: 2

Brand: Sabo Pages: 76

Brand: xsto Pages: 63

Brand: Joyolight Pages: 4

SynCore RW Unit

Brand: Ridder Pages: 28

Brand: Southern States Pages: 36

Brand: SOMFY Pages: 10

WEIDER SHAPE GLIDER WECR43062

Brand: ICON Health & Fitness Pages: 6

Brand: Duracell Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands