Simrad GO XSE Series Operator'S Manual Download Page 199 | Manualshive

Page: 199 / 242

background image

•

Close
Sets the alarm state to acknowledged. The siren/buzzer stops
and the alarm dialog is removed.
However, the alarm remains active in the alarm listing until the
reason for the alarm has been removed.

•

Disable
Disables the current alarm setting. The alarm does not show
again unless you turn it back on in the alarm settings dialog.

There is no time-out on a message or the siren. They remain active
until they are acknowledged or until the reason for the message is
rectified.

Alarms

Siren enable

Enables or disables the internal and external audio alarms when an
alarm condition arises.

Alarm dialogs

The alarm dialogs are activated from the Alarm settings dialog or by
selecting the Alarm button on the toolbar.

Alarms

| GO XSE/XSR Operator Manual

199

«
...
197
198
199
200
201
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: Gardena Pages: 13

WJHD309 - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 7

WJ-ND300 Administrator Console

Brand: Panasonic Pages: 24

Brand: lancer Pages: 12

Brand: Bahco Pages: 9

ABS-Lock DH04 Series

Brand: ABS Pages: 4

Brand: Datavideo Pages: 28

Brand: ParaBody Pages: 5

Brand: Ognibene Pages: 28

Brand: Hameg Pages: 24

Brand: Vaisala Pages: 118

Brand: Velleman Pages: 16

Brand: Velleman Pages: 11

Brand: Jackson Pages: 2

Brand: Vag Pages: 10

Cell Saver Elite+

Brand: Haemonetics Pages: 230

Brand: Tadano Pages: 16

Brand: Garmat Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands