Simrad GO XSE Series Operator'S Manual Download Page 221

Page: 221 / 242

Software updates

Before initiating an update to the unit, be sure to back up any
potentially valuable user data. Refer to

"Backing up your system data"

page 224.

Installed software and software updates

The about dialog shows the software version currently installed on
this unit (

If the unit is connected to internet, the dialog also shows available
software updates (

Update the software when connected to internet

If the unit is connected to internet, the system will automatically
check for software updates for the unit and for connected devices.

Note:

Some software update files might be larger than the

space available in the unit. If so, you will be prompted to insert a
storage device.

Maintenance

| GO XSE/XSR Operator Manual

221

Summary of Contents for GO XSE Series



















































































































































































































































Search results

Summary of Contents for GO XSE Series

Reviews:

Related manuals for GO XSE Series

Brands by name

Popular brands

Simrad GO XSE Series, Operator'S Manual

Search results

Summary of Contents for GO XSE Series

Reviews:

Related manuals for GO XSE Series

Brands by name

Popular brands