Q700M/Q500M SEDEO LITE
SEAT MOUNTING MATRIX
© 2021 Sunrise Medical (US) LLC
03/2021 P/N 253324 Rev. B
Pg 1 of 9
Customer service: +1 (800) 333-4000
or visit www.SunriseMedical.com
Please read these instructions carefully before beginning the assembly. Failure to understand and
follow assembly instructions may result in injury to technician and/or end user and may void the
warranty. If you have any questions call Sunrise Medical Technical Support at +1 (800) 333-4000.
Parts:
1. 4 ea Adapter plate screws (A)
2. 4 ea Seat screws (B)
3. 1 ea Adapter plate RH (C)
4. 1 ea Adapter plate LH (D)
5. 6 ea Interface screws (E)
6. 1 ea SEDEO Lite Seat (F)
7. 1 ea Module (Tilt, Lift, Tilt Lift Combo,
Filler) (G)
8. 1 ea Interface (H)
A. REMOVE SEAT/ADAPTER PLATES/ MODULE
1. Remove Seat (F):
Note position of seat screws (B) on the
seat (F) as well as the position to the adapter plates (C, D).
Remove the 4 seat screws (B) holding the seat to the
adapter (C, D) and remove the seat (F) (Fig 1). (Use 5mm
hex key)
2. Remove adapter plates (C and D):
If your chair does not
have adapter plates (C, D) skip this step, move on to step 3.
Note the position of the adapter screws (A) to the plates (C,
D) as well as to the module (G). Remove the 4 screws (A)
holding the adapter (C, D) to the module (G) and remove
the adapter plates (C, D) (Fig 1). (Use 5mm hex key)
Note- tilt module is shown, but directions apply to all
modules (lift, tilt, tilt lift combo, or ller).
3. Remove module (G):
Note the position of the interface
screws (E) to the interface (H) as well as to the module (G).
Remove the 6 screws (E) holding the module (G) to the
interface (H) and remove the module (G) (Fig 1). (Use 6mm
hex key)
4. Note position of all mounting locations
if the seat depth is
not changing. If the seat depth is changing, see pages 3-8.
B. ASSEMBLE SEAT/ADAPTER PLATES/ MODULE
1. Assemble module (G) to the interface (H)
using the
interface screws (E). See page 2 for mounting
location. Torque to 13.6-14.9Nm [120-132 in-lbs].
2. Assemble adapter plates (C, D) to module (G)
. If adapter
plates (C, D) are not used, skip this step and move on to
step 3. See pages 3-8 for mounting location.
Torque to 13.6-14.9Nm [120-132 in-lbs].
3. Assemble seat (F) to the adapter plates (C, D) or the
module (G)
using the seat screws (B). See pages 3-8 for
mounting location, and page 9 for seat depth detail.
Torque to 13.6-14.9Nm [120-132 in-lbs].
C. INSPECT:
1. All torque values with a torque wrench.
2. Ensure that all the wire harnesses are out of the way and
are not being pinched.
3. Verify that the harnesses are not put under tension in any
position.
4. Ensure the screws are mounted in the same location as they
were before removal or are mounted to new seat depth
locations as speci ed in Mounting Matrices below.
Required tools:
1. 5mm hex key
2. 6mm hex key
3. Torque wrench
DEALER/TECHNICIAN WARNING
Attention dealers and quali ed technicians, do not operate or service
this device without rst reading the owners manual. If you do not
understand the instructions and warnings in the owners manual please
contact the Quickie Technical Service Department before operating
and/or servicing the Quickie device. Failure to do so may result in
damage and/or injury.
Find more information and important warnings see the wheelchair
owner’s manual or at: www.SunriseMedical.com
Interface
screws (E)
SEDEO Lite Seat(F)
1
Seat screws (B)
Adapter Plate
screws (A)
Adapter Plate
Right Hand (C)
Adapter Plate
Left Hand (D)
Note
mounting
locations
Module (G)
Interface (H)
