manualshive.com logo in svg

Rohde & Schwarz SMBV100B, User Manual

Share
Download
Rohde & Schwarz SMBV100B User Manual Download Page 95

Configuring the Internal Baseband Source

R&S

®

SMBV100B

93

User Manual 1178.4460.02 ─ 03

the steepness of this ramp, see 

"Impact of the Power Ramping Settings on the

Generated Signal"

 

on page 93.

●

Level attenuation control signal

The "Lev_Att" signal is a rectangular pulse signal with variable low and high peri-
ods. Level attenuation is applied, if the "Lev_Att" signal is high. If level attenuation
is enabled, the modulation signal level is attenuated by a defined value.

Related settings:

●

Chapter 3.5.3.6, "Power Ramp Control Settings"

, 

on page 126

Possible applications

●

Use the "Level Attenuation" function to simulate radio stations located at various
distances.

●

Use the "Power Ramp" function if it is necessary to control the RF output signal
envelope synchronously, e.g. by the generation of TDMA signals.

Both the GSM/EDGE and the TD-SCDMA firmware options are equipped with embed-
ded power ramping function. In the GSM/EDGE standard for example, a maximum of 7
different level attenuation values can be defined and allocated separately to the 8 slots
independently of one another.

Impact of the Power Ramping Settings on the Generated Signal

The 

Figure 3-2

 explains the power ramping function in principle. The "Burst Gate" sig-

nal defines the start of the rising and falling edges of the envelope of the output signal,
and the "Lev Att" signal defines the start and end of level attenuation. The signal level
during the attenuation period is a configurable value.

Figure 3-2: Signal behavior when power ramping and level attenuation are enabled

Several parameters are provided for precise definition of the form and the steepness of
ramp. The 

Figure 3-3

 depicts the impact of the provided settings.

●

Ramp function: defines the shape of the rising and falling edges

●

Ramp time: defines the duration of the rising and the falling ramp

Common Functions and Settings in the Baseband Domain

Summary of Contents for SMBV100B







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands