manualshive.com logo in svg

Renesas SH7751 Group, User Manual

The Renesas SH7751 Group product offers a comprehensive User Manual that can be easily downloaded for free from our website. This manual provides detailed instructions and essential information for users to maximize the potential of their Renesas SH7751 Group device. Get your free manual at manualshive.com.

Share
Download
background image

SH7751 Group, SH7751R Group 

Section 22   PCI Controller (PCIC) 

R01UH0457EJ0301  Rev. 3.01 

 

Page 885 of 1128 

Sep 24, 2013 

 

The PCICR register is initialized at a power-on reset to H'000000*0 (bits 7 and 6 are initialized to 
B'00, and bits 5 and 4 sample the value of mode pins 9 and 10). At a software reset, bit 1 
(RSTCTL) is not initialized. All other bits are initialized in the same way as at a software reset. 

This register can be written to only when bits 31 to 24 are H'A5. 

Always set bit 0 (CFINIT) to 1 on completion of PCIC register initialization. 

Bits 31 to 10—Reserved: 

These bits are always read as 0. When writing, write H'A5 to bits 31 to 

24, and 0 to others. 

Bit 9—Target Read Single Buffer (TRDSGL): 

This bit specifies whether one target read buffer 

(32 bytes) or two target read buffers (64 bytes) are used for target memory read access to the 
PCIC. When two target read buffers faces are used, the data from two buffers are read via the local 
bus in advanced.

 

Bit 9:  TRDSGL 

Description 

0 

Use 2 target read buffers 

(Initial value) 

1 

Use 1 target read buffer only 

 

Bit 8—Data Byte Swap 

(

BYTESWAP): 

Specifies whether the data byte is swapped when the 

PCIC performs PIO transfer. 

Bit 8:  BYTESWAP 

Description 

0 

Send data as-is 

(Initial value) 

1 

Swap data byte before sending 

Note:  For details, refer to section 22.4, Endians. 

 

Bit 7—PCI Signal Pull-up (PCIUP): 

Controls the pull-up resistance of the PCI signal. Regarding 

the pins that are subject to pull-up, refer to table 22.1. Regarding the pull-up control provided 
when the 

PCIPEQ2

/MD9, 

PCIREQ3

/MD10 or 

PCIREQ4

 is used as a port, refer to the section on 

port control register (PCIPCTR). 

Bit 7:  PCIUP 

Description 

0 Pull-up 

(Initial 

value) 

1 No 

pull-up 

 

Summary of Contents for SH7751 Group



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7751 Group

MA lighting grandMA2 Series Quick Manual preview
grandMA2 Series
Brand: MA lighting Pages: 36
M86 Security R3000 Series Evaluation Manual preview
R3000 Series
Brand: M86 Security Pages: 46
H3C S5120V3-EI Series Manual preview
S5120V3-EI Series
Brand: H3C Pages: 54
Ublox LENA-R8 Series System Integration Manual preview
LENA-R8 Series
Brand: Ublox Pages: 116
Alacritech 1000x1 Hardware Installation Manual preview
1000x1
Brand: Alacritech Pages: 20
KEMP Technologies LoadMaster 1500 Installation And Configuration Manual preview
LoadMaster 1500
Brand: KEMP Technologies Pages: 71
XMOS XC-2 Quick Start Manual preview
XC-2
Brand: XMOS Pages: 6
Telit Wireless Solutions HE922-3GR Hardware User'S Manual preview
HE922-3GR
Brand: Telit Wireless Solutions Pages: 113
ICP DAS USA PISO-725 Series Quick Start Manual preview
PISO-725 Series
Brand: ICP DAS USA Pages: 8
ICP DAS USA USB-87P1 User Manual preview
USB-87P1
Brand: ICP DAS USA Pages: 62
ZALMAN CNPS7700 LED User Manual preview
CNPS7700 LED
Brand: ZALMAN Pages: 9
Promise Technology FastTrak TX4000 User Manual preview
FastTrak TX4000
Brand: Promise Technology Pages: 76
Kentrox RMM-1400 Configuration Manual preview
RMM-1400
Brand: Kentrox Pages: 246
UMAX Technologies SuperMac E100 User Manual preview
SuperMac E100
Brand: UMAX Technologies Pages: 27
Extreme Networks ExtremeCloud Appliance E1120 User Manual preview
ExtremeCloud Appliance E1120
Brand: Extreme Networks Pages: 219
NuDAQ ACL-8112 Series User Manual preview
ACL-8112 Series
Brand: NuDAQ Pages: 92
Intel 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011 Datasheet preview
2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011
Brand: Intel Pages: 172
Kodak X-Omat 1000 Service Manual preview
X-Omat 1000
Brand: Kodak Pages: 86

Brands by name

Popular brands

Load more brands