manualshive.com logo in svg

Renesas SH7751 Group, User Manual

The Renesas SH7751 Group product offers a comprehensive User Manual that can be easily downloaded for free from our website. This manual provides detailed instructions and essential information for users to maximize the potential of their Renesas SH7751 Group device. Get your free manual at manualshive.com.

Share
Download
background image

SH7751 Group, SH7751R Group 

Section 22   PCI Controller (PCIC) 

R01UH0457EJ0301  Rev. 3.01 

 

Page 921 of 1128 

Sep 24, 2013 

 

Bits 31 to 2—Reserved: 

These bits are always read as 0. When writing, always write H'A5 to bits 

31 to 24, and 0 to the other bits. Always write 0 to these bits when writing. 

Bit 1—PCICLK Stop Control 

(

PCICLKSTOP): 

Controls the stopping of the clock input via the 

PCICLK pin. 

Bit 1:  PCICLKSTOP 

Description 

0 

PCICLK input enabled 

(Initial 

value) 

1 

Stop PCICLK input 

 

Bit 0—BCLK Stop Control 

(

BCLKSTOP): 

Controls the stopping of the Bck input clock and 

CKIO input clock in the PCIC. 

Bit 0:  BCLKSTOP 

Description 

0 

Bck input enabled 

(Initial 

value) 

1 

Stop Bck input 

 

22.2.38

 

PCIC-BSC Registers 

PCIC Bus Control Register 1 (PCIBCR1) 
PCIC Bus Control Register 2 (PCIBCR2) 
PCIC Bus Control Register 3 (PCIBCR3)*

1

 

PCIC Wait Control Register 1 (PCIWCR1) 
PCIC Wait Control Register 2 (PCIWCR2) 
PCIC Wait Control register 3 (PCIWCR3) 
PCIC Discrete Memory Control Register (PCIMCR) 

Because PCI bus data is stored, in the PCIC, in memory on the local bus, the PCIC is equipped 
with an internal bus controller (PCIC-BSC). The PCIC-BSC performs the same type of control as 
the slave function of the bus controller (BSC). However, the PCIC-BSC returns bus rights to the 
BSC after each data transfer of up to 32 bytes of data. There are six registers in the PCIC-BSC: 
PCIBCR1 (equivalent to the BCR1 of the BSC), PCIBCR2 (equivalent to the BCR2 of the BSC), 
PCIBCR3 (equivalent to the BCR3 of the BSC)*

1

, PCIWCR1 (equivalent to the WCR1 of the 

BSC), PCIWCR2 (equivalent to the WCR2 of the BSC), PCIWCR3 (equivalent to the WCR3 of 
the BSC), and PCIMCR (equivalent to the MCR of the BSC). Each is a 32-bit register. BCR2 and 
BCR3 are 16-bit registers, but PCIBCR2 and PCIBCR3 should be accessed by longword access. 
The low 16 bits of PCIBCR2 and PCIBCR3 corresponds to the 16 bits of these registers, 
respectively. See section 13, Bus State Controller (BSC), for details of the initial values, etc.  

Summary of Contents for SH7751 Group



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7751 Group

Aleratec 310108 Quick Start Manual preview
310108
Brand: Aleratec Pages: 12
Acqiris SA217P Startup Manual preview
SA217P
Brand: Acqiris Pages: 22
Nvidia nForce 680I LT SLI Hardware User Manual preview
nForce 680I LT SLI
Brand: Nvidia Pages: 80
LSI MegaRAID SATA 300-4XLP Quick Installation Manual preview
MegaRAID SATA 300-4XLP
Brand: LSI Pages: 3
8e6 Technologies ER3-100 (5K02-55) Quick Start Manual preview
ER3-100 (5K02-55)
Brand: 8e6 Technologies Pages: 74
Allnet ALL1682504 Quick Installation preview
ALL1682504
Brand: Allnet Pages: 12
Telebyte 458-LM-E2-36 Quick Start Manual preview
458-LM-E2-36
Brand: Telebyte Pages: 19
Sennheiser Surround Dongle User Manual preview
Surround Dongle
Brand: Sennheiser Pages: 18
XMOS XC-2 Quick Start Manual preview
XC-2
Brand: XMOS Pages: 6
NEC Thin Client US310e Getting Started preview
Thin Client US310e
Brand: NEC Pages: 6
Supermicro Optane Persistent Memory 200 Series User Manual preview
Optane Persistent Memory 200 Series
Brand: Supermicro Pages: 54
Marani LPP-440A User Manual preview
LPP-440A
Brand: Marani Pages: 39
ICP DAS USA iWSN-200E Quick Start Manual preview
iWSN-200E
Brand: ICP DAS USA Pages: 8
Penguin Edge MVME2500 Quick Start Manual preview
MVME2500
Brand: Penguin Edge Pages: 2
NEC uPD75P3116 Datasheet preview
uPD75P3116
Brand: NEC Pages: 70
ETAS ES1392.1 User Manual preview
ES1392.1
Brand: ETAS Pages: 36
Alvarion BreezeNET DS.11 Configuration Utility Release Note preview
BreezeNET DS.11 Configuration Utility
Brand: Alvarion Pages: 2
Beck com.tom INDUSTRY 100.WLAN.W Startup Manual preview
com.tom INDUSTRY 100.WLAN.W
Brand: Beck Pages: 2

Brands by name

Popular brands

Load more brands