manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 64 of 760

31

9

VPN

Virtual address (1-kbyte page)

Virtual address (4-kbyte page)

TLB entry

Offset

VPN

VPN (31–17) VPN (11–10) ASID

V

PPN

D

Offset

0

10

31

11

0

(15)

(2)

(19)

(8)

SH

(1)

(1)

C

PR

(2)

SZ

(1) (1)

(1)

12

  VPN:  Virtual page number. Top 22 bits of virtual address for a 1-kbyte page, or top 20 bits of 

virtual address for a 4-kbyte page. Since VPN bits 16-12 are used as the index number, they 
are not stored in the TLB entry.

  ASID:  Address space identifier. Indicates the process that can access a virtual page. In single 

virtual memory mode and user mode, or in multiple virtual memory mode, if the SH bit is 0, 
the address is compared with the ASID in PTEH when address comparison is performed.

 

SH:  Share status bit

 

  0 = Page not shared between processes

 

  1 = Page shared between processes

 SZ: 

Page-size 

bit

 

  0 = 1-kbyte page

 

  1 = 4-kbyte page

 

V:  Valid bit. Indicates whether entry is valid.

 

  0 = Invalid

 

  1 = Valid

 

  Cleared to 0 by a power-on reset. Not affected by a manual reset.

  PPN:  Physical page number. Top 29 bits of physical address. PPN bits 11-10 are not used in case 

of a 4-kbyte page. Attention must be paid to the synonym problem in case of a 1-kbyte page 
(see section 3.4.4, Avoiding Synonym Problems).

      PR:   Set the most significant bit to 0.
 

  Protection key field. 2-bit field encoded to define the access rights to the page.

 

  00: Reading only is possible in privileged mode.

 

  01: Reading/writing is possible in privileged mode.

 

  10: Reading only is possible in privileged/user mode.

 

  11: Reading/writing is possible in privileged/user mode.

 

C:  Cacheable bit. Indicates whether the page is cacheable.

  

0: 

Non-cacheable

  

1: 

Cacheable

 

D:  Dirty bit. Indicates whether the page has been written to.

 

  0 = Not written to

 

  1 = Written to

Legend:

Figure 3.5   Virtual Address and TLB Structure

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Brand: Infoblox Pages: 13
EMS 2000 IDU Series User Manual preview
2000 IDU Series
Brand: EMS Pages: 52
IBM Power System H924 Installing Instructions preview
Power System H924
Brand: IBM Pages: 48
Trend Micro IPS Pro-Module-24C-GE-BP-TM Quick Setup Manual preview
IPS Pro-Module-24C-GE-BP-TM
Brand: Trend Micro Pages: 3
Cabletron Systems MMAC-Plus 9G536-04 User Manual preview
MMAC-Plus 9G536-04
Brand: Cabletron Systems Pages: 42
ASROCK H670M PRO RS Manual preview
H670M PRO RS
Brand: ASROCK Pages: 173
Rosewill RCX-Z5 User Manual preview
RCX-Z5
Brand: Rosewill Pages: 2
JAKA MiniCab Hardware User Manual preview
MiniCab
Brand: JAKA Pages: 37
Renesas H8S/2646 Series User Manual preview
H8S/2646 Series
Brand: Renesas Pages: 20
LaView LV-KN series Quick Start Manual preview
LV-KN series
Brand: LaView Pages: 2
ExtraHop EDA 4200 Install preview
EDA 4200
Brand: ExtraHop Pages: 2
MCT MPU100ZW User Manual preview
MPU100ZW
Brand: MCT Pages: 12
DPS Telecom D-PK-NG432 User Manual preview
D-PK-NG432
Brand: DPS Telecom Pages: 80
Grizzly PSJ-VZ58 gen3 OEM User Manual preview
PSJ-VZ58 gen3 OEM
Brand: Grizzly Pages: 12
Renesas M32173T-PTC User Manual preview
M32173T-PTC
Brand: Renesas Pages: 7
ADTRAN 1200127L1 User Manual preview
1200127L1
Brand: ADTRAN Pages: 20
ZALMAN CNPS2005-Plus User Manual preview
CNPS2005-Plus
Brand: ZALMAN Pages: 6
KEB 1MF5280-7008 Instruction Manual preview
1MF5280-7008
Brand: KEB Pages: 32

Brands by name

Popular brands

Load more brands