manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 92 of 760

4.3

Register Descriptions

There are four registers related to exception handling. These are peripheral module registers, and
therefore reside in area P4. They can be accessed by specifying the address in privileged mode
only.

1. The exception event register (EXPEVT) resides at address H'FFFFFFD4, and contains a 12-bit

exception code. The exception code set in EXPEVT is that for a reset or general exception
event. The exception code is set automatically by hardware when an exception occurs.
EXPEVT can also be modified by software.

2. The interrupt event register (INTEVT) resides at address H'FFFFFFD8, and contains a 12-bit

interrupt exception code or a code indicating the interrupt priority. Which is set when an
interrupt occurs depends on the interrupt source (see tables 6.4 and 6.5). The exception code or
interrupt priority code is set automatically by hardware when an exception occurs. INTEVT
can also be modified by software.

3. Interrupt event register 2 (INTEVT2) resides at address H'04000000, and contains a 12-bit

exception code. The exception code set in INTEVT2 is that for an interrupt request. The
exception code is set automatically by hardware when an exception occurs.

4. The TRAPA exception register (TRA) resides at address H'FFFFFFD0, and contains 8-bit

immediate data (imm) for the TRAPA instruction. TRA is set automatically by hardware when
a TRAPA instruction is executed. TRA can also be modified by software.

The bit configurations of the EXPEVT, INTEVT, INTEVT2, and TRA registers are shown in
figure 4.3.

31

0

0 Exception code

imm

00

11

0

EXPEVT, INTEVT, and INTEVT2 registers

8-bit immediate data in TRAPA instruction

imm:

0:

Reserved bits, always read as 0

31

0

0

9

2

0

TRA register

Figure 4.3   Bit Configurations of EXPEVT, INTEVT, INTEVT2, and TRA Registers

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Brand: Panasonic Pages: 4
B2 ABB2050 Instruction Manual preview
ABB2050
Brand: B2 Pages: 52
Samsung NAS Series Hardware User Manual preview
NAS Series
Brand: Samsung Pages: 65
LORD AP5103 Series Technical Manual preview
AP5103 Series
Brand: LORD Pages: 9
UfiSpace S9600-64X Hardware Installation Manual preview
S9600-64X
Brand: UfiSpace Pages: 35
Point of View SmartTV 210 User Manual preview
SmartTV 210
Brand: Point of View Pages: 13
ICP DAS USA PDS-734D Quick Start Manual preview
PDS-734D
Brand: ICP DAS USA Pages: 8
Comtrend Corporation WAP-5922MP Quick Install Manual preview
WAP-5922MP
Brand: Comtrend Corporation Pages: 4
Eastern Voltage Research Advanced Flame 1.0 Instruction Manual preview
Advanced Flame 1.0
Brand: Eastern Voltage Research Pages: 12
ADTRAN TRACER 5045 Manual preview
TRACER 5045
Brand: ADTRAN Pages: 9
Radica Games DAVID-II 716 Operating And Maintenance Instruction Manual preview
DAVID-II 716
Brand: Radica Games Pages: 40
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Renesas HD74HCT1G04 Datasheet preview
HD74HCT1G04
Brand: Renesas Pages: 8
H3C SecPath F50X0 Series Manual preview
SecPath F50X0 Series
Brand: H3C Pages: 41
Altronix NetWay8GL Installation Manual preview
NetWay8GL
Brand: Altronix Pages: 8
Opengear OG-HDTV-SDI-UHD User Manual preview
OG-HDTV-SDI-UHD
Brand: Opengear Pages: 7
Cypress Semiconductor CY7C1440AV33 Specification Sheet preview
CY7C1440AV33
Brand: Cypress Semiconductor Pages: 31
Intel RS2BL040 - Raid Controller Configuration Manual preview
RS2BL040 - Raid Controller
Brand: Intel Pages: 5

Brands by name

Popular brands

Load more brands