manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 517 of 760

16.2

Register Descriptions

16.2.1

Receive Shift Register (SCRSR)

The receive shift register (SCRSR) receives serial data. Data input at the RxD pin is loaded into
SCRSR in the order received, LSB (bit 0) first, converting the data to parallel form. When one
byte has been received, it is automatically transferred to SCFRDR, the receive FIFO data register.
The CPU cannot read or write to SCRSR directly.

Bit:

7

6

5

4

3

2

1

0

R/W:

—

—

—

—

—

—

—

—

16.2.2

Receive FIFO Data Register (SCFRDR)

The 16-byte receive FIFO data register (SCFRDR) stores serial receive data. The SCIF completes
the reception of one byte of serial data by moving the received data from the receive shift register
(SCRSR) into SCFRDR for storage. Continuous reception is possible until 16 bytes are stored.

The CPU can read but not write to SCFRDR.  If data is read when there is no receive data in the
SCFRDR, the value is undefined. When this register is full of receive data, subsequent serial data
is lost.

Bit:

7

6

5

4

3

2

1

0

R/W:

R

R

R

R

R

R

R

R

16.2.3

Transmit Shift Register (SCTSR)

The transmit shift register (SCTSR) transmits serial data. The SCI loads transmit data from the
transmit FIFO data register (SCFTDR) into SCTSR, then transmits the data serially from the TxD
pin, LSB (bit 0) first. After transmitting one data byte, the SCI automatically loads the next
transmit data from SCFTDR into SCTSR and starts transmitting again.  The CPU cannot read or
write to SCTSR directly.

Bit:

7

6

5

4

3

2

1

0

R/W:

—

—

—

—

—

—

—

—

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Radwin Transportation FiberinMotion Deployment Manual preview
Transportation FiberinMotion
Brand: Radwin Pages: 122
TC Electronic ATAC Service Manual preview
ATAC
Brand: TC Electronic Pages: 55
Teagle Tomahawk 7100 Operator'S Manual preview
Tomahawk 7100
Brand: Teagle Pages: 40
Q-See QC814 Specifications preview
QC814
Brand: Q-See Pages: 2
Avolites Titan One Quick Start Manual preview
Titan One
Brand: Avolites Pages: 24
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Brand: Zhone Pages: 114
B-G Instruments DataPlot CB1224 Manual preview
DataPlot CB1224
Brand: B-G Instruments Pages: 4
Abit G740A Installation Manual And User'S Manual preview
G740A
Brand: Abit Pages: 22
Hafele Suzie-Q 541.35.520 Mounting Instructions preview
Suzie-Q 541.35.520
Brand: Hafele Pages: 12
MA lighting 8Port Node Quick Manual preview
8Port Node
Brand: MA lighting Pages: 49
Magewell XI100DUSB-SDI User Manual preview
XI100DUSB-SDI
Brand: Magewell Pages: 10
Z3 Technology Z3-HE2160-RPS User Instructions preview
Z3-HE2160-RPS
Brand: Z3 Technology Pages: 18
Keithley 7075 Instruction Manual preview
7075
Brand: Keithley Pages: 108
RAK RAK1901 Quick Start Manual preview
RAK1901
Brand: RAK Pages: 14
Proxim 68568r1 Installation And Management Manual preview
68568r1
Brand: Proxim Pages: 65
Datel DataMAX User Manual preview
DataMAX
Brand: Datel Pages: 8
NetApp NS224 Instructions Manual preview
NS224
Brand: NetApp Pages: 28
Extron electronics Dual Window Multi-Graphic Processor MGP 462 Specifications preview
Dual Window Multi-Graphic Processor MGP 462
Brand: Extron electronics Pages: 2

Brands by name

Popular brands

Load more brands