manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 537 of 760

16.3

Operation

16.3.1

Overview

For serial communication, the SCIF has an asynchronous mode in which characters are
synchronized individually.  Refer to section 14.3.2, Operation in Asynchronous Mode.  The SCIF
has a 16-byte FIFO buffer for both transmit and receive operations, reducing the overhead of the
CPU, and enabling continuous high-speed communication.  Moreover, it has 

RTS

 and 

CTS

 signals

as modem control signals.  The transmission format is selected in the serial mode register
(SCSMR), as shown in table 16.7. The SCIF clock source is selected by the combination of the
CKE1 and CKE0 bits in the serial control register (SCSCR), as shown in table 16.8.

•

 

Data length is selectable: 7 or 8 bits.

•

 

Parity and multiprocessor bits are selectable, as is the stop bit length (1 or 2 bits). The
combination of the preceding selections constitutes the communication format and character
length.

•

 

In receiving, it is possible to detect framing errors (FER), parity errors (PER), receive FIFO
data full, receive data ready, and breaks.

•

 

In transmitting, it is possible to detect transmit FIFO data empty.

•

 

The number of stored data bytes is indicated for both the transmit and receive FIFO registers.

•

 

An internal or external clock can be selected as the SCIF clock source.

 

When an internal clock is selected, the SCIF operates using the on-chip baud rate
generator, and can output a serial clock signal with a frequency 16 times the bit rate.

 

When an external clock is selected, the external clock input must have a frequency 16 times
the bit rate. (The on-chip baud rate generator is not used.)

Table 16.7

SCSMR Settings and SCIF Communication Formats

SCSMR Settings

SCIF Communication Format

Mode

Bit 6
CHR

Bit 5
PE

Bit 3
STOP

Data
Length

Parity
Bit

Stop Bit Length

Asynchronous

0

0

0

8-bit

Not set

1 bit

1

2  bits

1

0

Set

1  bit

1

2  bits

1

0

0

7-bit

Not  set

1  bit

1

2  bits

1

0

Set

1  bit

1

2  bits

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Samsung SWC-E100 Quick Start Manual preview
SWC-E100
Brand: Samsung Pages: 2
Samsung iDCS 500 Manual preview
iDCS 500
Brand: Samsung Pages: 31
Samsung DDR3 Product Manual preview
DDR3
Brand: Samsung Pages: 15
Patton electronics 1090 Service Manual preview
1090
Brand: Patton electronics Pages: 8
XMOS xCORE-200 Multi-channel Audio board Design Manual preview
xCORE-200 Multi-channel Audio board
Brand: XMOS Pages: 112
Samsung NAS Series Hardware User Manual preview
NAS Series
Brand: Samsung Pages: 65
A10 Thunder Series Manual preview
Thunder Series
Brand: A10 Pages: 52
Allnet ALL1682504 Quick Installation preview
ALL1682504
Brand: Allnet Pages: 12
Telebyte 458-LM-E2-36 Quick Start Manual preview
458-LM-E2-36
Brand: Telebyte Pages: 19
Belden HIRESCHMANN IT MAMMUTHUS MTM8003-FAN User Manual preview
HIRESCHMANN IT MAMMUTHUS MTM8003-FAN
Brand: Belden Pages: 84
OWC Mercury FireWire 400 Owner'S Manual preview
Mercury FireWire 400
Brand: OWC Pages: 2
Quantum QWCM Installation Manual preview
QWCM
Brand: Quantum Pages: 7
ARTERY AT32F421 Series Reference Manual preview
AT32F421 Series
Brand: ARTERY Pages: 337
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Brand: GarrettCom Pages: 10
Adaptec 2410SA - Serial ATA RAID Controller Hardware Installation Manual preview
2410SA - Serial ATA RAID Controller
Brand: Adaptec Pages: 14
IFM QHA200 Instructions For Setup preview
QHA200
Brand: IFM Pages: 12
Renesas R0E424270CFLE0 User Manual preview
R0E424270CFLE0
Brand: Renesas Pages: 4
ADTRAN 1200127L1 User Manual preview
1200127L1
Brand: ADTRAN Pages: 20

Brands by name

Popular brands

Load more brands