manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 464 of 760

In receiving, the SCI operates as follows:

1. The SCI monitors the communication line. When it detects a start bit (0), the SCI synchronizes

internally and starts receiving.

2. Receive data is shifted into SCRSR in order from the LSB to the MSB.

3. The parity bit and stop bit are received. After receiving these bits, the SCI makes the following

checks:

a. Parity check: The number of 1s in the receive data must match the even or odd parity

setting of the O/

E

 bit in SCSMR.

b. Stop bit check: The stop bit value must be 1. If there are two stop bits, only the first stop bit

is checked.

c. Status check: RDRF must be 0 so that receive data can be loaded from SCRSR into

SCRDR.

If these checks all pass, the SCI sets RDRF to 1 and stores the received data in SCRDR. If
one of the checks fails (receive error), the SCI operates as indicated in table 14.12.

Note:

When a receive error flag is set, further receiving is disabled. The RDRF bit is not set to 1.
Be sure to clear the error flags.

4. After setting RDRF to 1, if the receive-data-full interrupt enable bit (RIE) is set to 1 in

SCSCR, the SCI requests a receive-data-full interrupt (RXI). If one of the error flags (ORER,
PER, or FER) is set to 1 and the receive-data-full interrupt enable bit (RIE) in SCSCR is also
set to 1, the SCI requests a receive-error interrupt (ERI).

Table 14.12 Receive Error Conditions and SCI Operation

Receive Error

Abbreviation

Condition

Data Transfer

Overrun error

ORER

Receiving of next data ends while
RDRF is still set to 1 in SCSSR

Receive data not
transferred from SCRSR
into SCRDR

Framing error

FER

Stop bit is 0

Receive data transferred
from SCRSR into SCRDR

Parity error

PER

Parity of receive data differs from
even/odd parity setting in SCSMR

Receive data transferred
from SCRSR into SCRDR

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

IBA Com-L2B-4-8 Manual preview
Com-L2B-4-8
Brand: IBA Pages: 29
Amplifier Tech ATP6700 Owner'S Manual preview
ATP6700
Brand: Amplifier Tech Pages: 36
Avolites Titan One Quick Start Manual preview
Titan One
Brand: Avolites Pages: 24
T.A HALL 6370 Instruction Manual preview
HALL 6370
Brand: T.A Pages: 11
Kanguru Data Bank User Manual preview
Data Bank
Brand: Kanguru Pages: 13
JETWAY HBJC924R3288DG2NS Series Quick Installation Manual preview
HBJC924R3288DG2NS Series
Brand: JETWAY Pages: 6
EVOC 6336-STG-YX Manual preview
6336-STG-YX
Brand: EVOC Pages: 57
Intel i960 Jx Developer'S Manual preview
i960 Jx
Brand: Intel Pages: 578
IEI Technology WAFER-ULT4 User Manual preview
WAFER-ULT4
Brand: IEI Technology Pages: 136
M-system M5XSBS Instruction Manual preview
M5XSBS
Brand: M-system Pages: 4
ATEN Altusen SN0100 Series User Manual preview
Altusen SN0100 Series
Brand: ATEN Pages: 178
Kontron PC/104-PCMCIA-1 User Manual preview
PC/104-PCMCIA-1
Brand: Kontron Pages: 20
ekwb EK-TIM Indigo Extreme Installation Manual preview
EK-TIM Indigo Extreme
Brand: ekwb Pages: 4
Hama 00062773 Quick Manual preview
00062773
Brand: Hama Pages: 10
ASTRO U 960 Operating Manual preview
U 960
Brand: ASTRO Pages: 12
FDI UEZGUI-4357-70WVN User Manual preview
UEZGUI-4357-70WVN
Brand: FDI Pages: 30
ICS Advent COMM4AT/EX Product Manual preview
COMM4AT/EX
Brand: ICS Advent Pages: 30
Curtiss-Wright KAD/UBM/105 Quick Start Manual preview
KAD/UBM/105
Brand: Curtiss-Wright Pages: 12

Brands by name

Popular brands

Load more brands