manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 115 of 760

5.4.3

Examples of Usage

(1) Invalidating a Specific Entry
A specific cache entry can be invalidated by accessing the allocated memory cache and writing a 0
to the entry’s U and V bits. The A bit is cleared to 0, and an address is specified for the entry
address and the way. If the U bit of the way of the entry in question was set to 1, the entry is
written back and the V and U bits specified by the write data are written to.

In the following example, the write data is specified in R0 and the address is specified in R1.

; R0 = H'0000 0000 LRU = H'000, U = 0, V = 0

; R1 = H'F000 1080, Way = 1, Entry = H'08, A = 0

;

MOV.L

R0, @R1

To invalidate all entries and ways, write 0 to the following addresses.

Addresses

F000 0000

F000 0010

F000 0020

    :

F000 3FF0

This involves a total of 1,024 writes.

The above operation should be performed using a non-cacheable area.

(2) Invalidating a Specific Address
A specific address can be invalidated by writing a 0 to the entry’s U and V bits. When the A bit is
1, the tag address specified by the write data is compared to the tag address within the cache
selected by the entry address. If the tag addresses match, data is written to the memory at that
address. If no match is found, no operation is carried out. If the entry’s U bit is 1 at that time, the
entry is written back.

; R0 = H'0110 0010; Tag address = B'0000 0001 0001 0000 0000 00, U = 0,

V = 0

; R1 = H'F000 0088; Address array access, Entry = H'08, A = 1

;

MOV.L

R0, @R1

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

8e6 Technologies Enterprise Filter Authentication R3000 Quick Start Manual preview
Enterprise Filter Authentication R3000
Brand: 8e6 Technologies Pages: 66
Lanner NCA-4035 User Manual preview
NCA-4035
Brand: Lanner Pages: 109
Roland VP-9000 Turbostart preview
VP-9000
Brand: Roland Pages: 2
Realtek RTL8187SE User Manual preview
RTL8187SE
Brand: Realtek Pages: 30
Magma ExpressBox2 EB2 User Manual preview
ExpressBox2 EB2
Brand: Magma Pages: 74
Renesas H8S/2437 Hardware Manual preview
H8S/2437
Brand: Renesas Pages: 746
Accusys ACS-7630 User Manual preview
ACS-7630
Brand: Accusys Pages: 34
ZALMAN ZM80C-HP Manual preview
ZM80C-HP
Brand: ZALMAN Pages: 18
Corsair H80i v2 Quick Start Manual preview
H80i v2
Brand: Corsair Pages: 12
ekwb EK-Quantum Vector TUF RX 6800 User Manual preview
EK-Quantum Vector TUF RX 6800
Brand: ekwb Pages: 14
ST STM32MP157 Series User Manual preview
STM32MP157 Series
Brand: ST Pages: 47
Netopia D3100-I User Reference Manual preview
D3100-I
Brand: Netopia Pages: 138
Patton electronics ForeFront 2616RC Getting Started Manual preview
ForeFront 2616RC
Brand: Patton electronics Pages: 80
soundsation DCX NET Series User Manual preview
DCX NET Series
Brand: soundsation Pages: 47
Extron electronics RGB 460xi FSR Series Installation Manual preview
RGB 460xi FSR Series
Brand: Extron electronics Pages: 9
Cisco 3005 Getting Started preview
3005
Brand: Cisco Pages: 122
Jupiter AJ120 User Manual preview
AJ120
Brand: Jupiter Pages: 9
Crestron HDMI Input Card DMC-HD Specifications preview
HDMI Input Card DMC-HD
Brand: Crestron Pages: 1

Brands by name

Popular brands

Load more brands