manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 192 of 760

8.6

Timing of STATUS Pin Changes

The timing of STATUS1 and STATUS0 pin changes is shown in figures 8.1 to 8.8.

8.6.1

Timing for Resets

Power-On Reset

CKIO, CKIO2

*

4

RESETP

STATUS

Normal

*

2

Normal

*

2

Reset

*

1

PLL settling

time

0 to 5 Bcyc

*

3

0 to 30 Bcyc

*

3

RESETOUT

Notes:  1.  Reset: 

HH (STATUS1 high, STATUS0 high)

 

2.  Normal:  LL (STATUS1 low, STATUS0 low)

 

3.  Bcyc: 

Bus clock cycle

 

4.  The CKIO2 output is available only in clock modes 0, 1, and 2.

Figure 8.2   Power-On Reset (Clock Modes 0, 1, 2, and 7) STATUS Output

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Abus TVVR36500 User Manual preview
TVVR36500
Brand: Abus Pages: 60
Internet Security Systems Proventia A1204 User Manual preview
Proventia A1204
Brand: Internet Security Systems Pages: 42
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Brand: Patton electronics Pages: 145
Cypress Semiconductor CY7C1303BV25 Specification Sheet preview
CY7C1303BV25
Brand: Cypress Semiconductor Pages: 19
Keysight Technologies U3024AH10 User'S And Service Manual preview
U3024AH10
Brand: Keysight Technologies Pages: 106
Dave Embedded Systems diDo Hardware Manual preview
diDo
Brand: Dave Embedded Systems Pages: 79
Microcomputer Systems MSI-P602 User Manual preview
MSI-P602
Brand: Microcomputer Systems Pages: 21
Lindy Modular Fast Fiber Switch Converter MT-RJ Specifications preview
Modular Fast Fiber Switch Converter MT-RJ
Brand: Lindy Pages: 3
ADLINK Technology AMC-7000 User Manual preview
AMC-7000
Brand: ADLINK Technology Pages: 34
Sennheiser GSP 300 User Manual preview
GSP 300
Brand: Sennheiser Pages: 22
Azoteq IQ Switch ProxSense RS100 Application Notes preview
IQ Switch ProxSense RS100
Brand: Azoteq Pages: 9
DarbeeVision Dablet DVP 5000 User Manual preview
Dablet DVP 5000
Brand: DarbeeVision Pages: 10
Extreme Networks ExtremeCloud Appliance E3120 Installation Manual preview
ExtremeCloud Appliance E3120
Brand: Extreme Networks Pages: 27
JETWAY 939GT2-Ultra Series User Manual preview
939GT2-Ultra Series
Brand: JETWAY Pages: 55
ICP DAS USA PEX-P8R8i Quick Start Manual preview
PEX-P8R8i
Brand: ICP DAS USA Pages: 9
A.E.B. 628450000 Assembly & Instruction Manual preview
628450000
Brand: A.E.B. Pages: 10
Extron electronics DVI Output Card Installation Manual preview
DVI Output Card
Brand: Extron electronics Pages: 6
Extron electronics IPL M PDP-ES User Manual preview
IPL M PDP-ES
Brand: Extron electronics Pages: 36

Brands by name

Popular brands

Load more brands