manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 417 of 760

13.2.12

Day of Week Alarm Register (RWKAR)

The day of week alarm register (RWKAR) is an 8-bit readable/writable register, and an alarm
register corresponding to the BCD-coded day of week section counter RWKCNT of the RTC.
When the ENB bit is set to 1, a comparison with the RWKCNT value is performed. From among
the RSECAR/RMINAR/RHRAR/RWKAR/RDAYAR/RMONAR registers, the counter and alarm
register comparison is performed only on those with ENB bits set to 1, and if each of those
coincide, an RTC alarm interrupt is generated.

The range that can be set is 0

–

6 (decimal) + ENB bit. Errant operation will result if any other

value is set.

The ENB bit in RWKAR is initialized by a power-on reset. The remaining RWKAR fields are not
initialized and retain their contents by a manual reset, or in standby mode.

Bit:

7

6

5

4

3

2

1

0

ENB

—

—

—

—

Day  of  week

Initial  value:

0

0

0

0

0

—

—

—

R/W:

R/W

R

R

R

R

R/W

R/W

R/W

Days of the week are coded as shown in table 13.4.

Table 13.4

Day-of-Week Codes (RWKAR)

Day of Week

Code

Sunday

0

Monday

1

Tuesday

2

Wednesday

3

Thursday

4

Friday

5

Saturday

6

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
NEC N8141-75F Startup Manual preview
N8141-75F
Brand: NEC Pages: 6
Telex Communications 2472AA Instruction Manual preview
2472AA
Brand: Telex Communications Pages: 28
Dolphin IBP-G4x16-2 User Manual preview
IBP-G4x16-2
Brand: Dolphin Pages: 9
Avaya PARTNER PC CARD Installation Instructions preview
PARTNER PC CARD
Brand: Avaya Pages: 4
National Instruments SCXI-1120 User Manual preview
SCXI-1120
Brand: National Instruments Pages: 130
Cytron Technologies SHIELD-2AMOTOR User Manual preview
SHIELD-2AMOTOR
Brand: Cytron Technologies Pages: 13
ICP DAS USA USB-87P1 User Manual preview
USB-87P1
Brand: ICP DAS USA Pages: 62
Advantech ARK-1380 User Manual preview
ARK-1380
Brand: Advantech Pages: 50
IBM Power System H924 Installing Instructions preview
Power System H924
Brand: IBM Pages: 48
Bose PowerMatch ESPLink Quick Start Manual preview
PowerMatch ESPLink
Brand: Bose Pages: 2
ebm-papst R3G560-AH02-03 Operating Instructions Manual preview
R3G560-AH02-03
Brand: ebm-papst Pages: 13
Microchip Technology PD-9501-10GCO/AC User'S Installation Manual preview
PD-9501-10GCO/AC
Brand: Microchip Technology Pages: 41
Ultra Products Internal All-in-One Digital Media Drive ULT31793 Specifications preview
Internal All-in-One Digital Media Drive ULT31793
Brand: Ultra Products Pages: 1
YASKAWA CP 040 RS422/485 Manual preview
CP 040 RS422/485
Brand: YASKAWA Pages: 87
ZALMAN ZM-RWB1 User Manual preview
ZM-RWB1
Brand: ZALMAN Pages: 6
Hakki Pilke 43 Pro Instructions For Assembly, Operation And Maintenance preview
43 Pro
Brand: Hakki Pilke Pages: 48
Tvone CORIOview MWP Series Quick Start Manual preview
CORIOview MWP Series
Brand: Tvone Pages: 24

Brands by name

Popular brands

Load more brands