manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 407 of 760

Section 13   Realtime Clock (RTC)

13.1

Overview

The SH7709S has a realtime clock (RTC) with its own 32.768-kHz crystal oscillator.

13.1.1

Features

•

 

Clock and calendar functions (BCD display): Seconds, minutes, hours, date, day of the week,
month, and year

•

 

1-Hz to 64-Hz timer (binary display)

•

 

Start/stop function

•

 

30-second adjust function

•

 

Alarm interrupt: Frame comparison of seconds, minutes, hours, date, day of the week, and
month can be used as conditions for the alarm interrupt

•

 

Cyclic interrupts: The interrupt cycle may be 1/256 second, 1/64 second, 1/16 second, 1/4
second, 1/2 second, 1 second, or 2 seconds

•

 

Carry interrupt: A carry interrupt indicates when a carry occurs during a counter read

•

 

Automatic leap year correction

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
RadiSys EPC-31 Hardware Reference Manual preview
EPC-31
Brand: RadiSys Pages: 44
Paradyne Comsphere 3510 User Manual preview
Comsphere 3510
Brand: Paradyne Pages: 85
Tandberg Data Storagelibrary T24 Manual preview
Storagelibrary T24
Brand: Tandberg Data Pages: 28
Aaeon SBC-657B Manual preview
SBC-657B
Brand: Aaeon Pages: 61
EZCast Pro Dongle II User Manual preview
Pro Dongle II
Brand: EZCast Pages: 24
Ista AMF2.0 Operator'S Manual preview
AMF2.0
Brand: Ista Pages: 16
ZALMAN RESERATOR2 Installation And Operational Manual preview
RESERATOR2
Brand: ZALMAN Pages: 18
Procool SP480 Series Instructions preview
SP480 Series
Brand: Procool Pages: 2
ADS Technologies PTV-370 Driver Manual preview
PTV-370
Brand: ADS Technologies Pages: 1
CSL 300295 User Manual preview
300295
Brand: CSL Pages: 24
Vivotek ND8212W Hardware Installation Manual preview
ND8212W
Brand: Vivotek Pages: 46
ST STEVAL-SCR002V1 User Manual preview
STEVAL-SCR002V1
Brand: ST Pages: 28
ACTi GNR-410 Quick Installation Manual preview
GNR-410
Brand: ACTi Pages: 12
Acces I/O products mPCIE-ADIO16-8F Series Hardware Manual preview
mPCIE-ADIO16-8F Series
Brand: Acces I/O products Pages: 13
M86 Security IR Web Filter User Manual preview
IR Web Filter
Brand: M86 Security Pages: 540
Boser HS-2621 Manual preview
HS-2621
Brand: Boser Pages: 54
CAMBRIONIX OEM-U8S User Manual preview
OEM-U8S
Brand: CAMBRIONIX Pages: 43

Brands by name

Popular brands

Load more brands