manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 149 of 760

Section 7   User Break Controller

7.1

Overview

The user break controller (UBC) provides functions that simplify program debugging. This
function makes it easy to design an effective self-monitoring debugger, enabling the chip to debug
programs without using an in-circuit emulator. Break conditions that can be set in the UBC are
instruction fetch or data read/write, data size, data content, address value, and stop timing during
instruction fetches.

7.1.1

Features

The user break controller has the following features:

•

 

The following break comparison conditions can be set.

Number of break channels: two channels (channels A and B)
User break can be requested as either the independent or sequential condition on channels A
and B (sequential break setting: channel A and, then channel B match with logical AND, but
not in the same bus cycle).

Address (Compares 40 bits comprised of a 32-bit logical address prefixed with an ASID
address. Comparison bits are maskable in 32-bit units, user can easily program it to mask
addresses at bottom 12 bits (4-k page), bottom 10 bits (1-k page), or any size of page, etc.

One of two address buses (CPU address bus (LAB), cache address bus (IAB)) can be
selected.

 

Data (only on channel B, 32-bit maskable)

 

One of the two data buses (CPU data bus (LDB), cache data bus (IDB)) can be selected.

 

Bus master: CPU cycle or DMAC cycle

 

Bus cycle: instruction fetch or data access

 

Read/write

 

Operand size: byte, word, or longword

•

 

User break is generated upon satisfying break conditions. A user-designed user-break
condition exception processing routine can be run.

•

 

In an instruction fetch cycle, it can be selected that a break is set before or after an instruction
is executed.

•

 

Maximum repeat times for the break condition: 2

12

 – 1 times.

•

 

Eight pairs of branch source/destination buffers.

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

NEC N8104-213 Installation Manual preview
N8104-213
Brand: NEC Pages: 10
NEC N8104-213 Instructions Manual preview
N8104-213
Brand: NEC Pages: 8
Ebyte E43-900T13S3 Manual preview
E43-900T13S3
Brand: Ebyte Pages: 8
Vonets MINI300 Quick Setting Manual preview
MINI300
Brand: Vonets Pages: 8
ekwb EK-FC Installation Manual preview
EK-FC
Brand: ekwb Pages: 2
IBA ibaFOB-4i-X Manual preview
ibaFOB-4i-X
Brand: IBA Pages: 33
Paradyne iMarc SLV 9820-2M Installation Instructions Manual preview
iMarc SLV 9820-2M
Brand: Paradyne Pages: 24
ZALMAN CNPS9500 AT User Manual preview
CNPS9500 AT
Brand: ZALMAN Pages: 9
CAME ZG6 Installation Manual preview
ZG6
Brand: CAME Pages: 14
Akasa Venom A10 User Manual preview
Venom A10
Brand: Akasa Pages: 2
National Instruments GPIB-120A User Manual preview
GPIB-120A
Brand: National Instruments Pages: 36
IEI Technology PUZZLE-5030 User Manual preview
PUZZLE-5030
Brand: IEI Technology Pages: 119
ZALMAN CNPS7000B Series User Manual preview
CNPS7000B Series
Brand: ZALMAN Pages: 9
TRENDnet TEG-S3M8S15 Specifications preview
TEG-S3M8S15
Brand: TRENDnet Pages: 2
NEC LCD4020-2-IT - MultiSync - 40" LCD Flat Panel Display Installation Manual preview
LCD4020-2-IT - MultiSync - 40" LCD Flat Panel Display
Brand: NEC Pages: 9
NEC M40 - MULTEOS - 40" LCD TV Brochure & Specs preview
M40 - MULTEOS - 40" LCD TV
Brand: NEC Pages: 24
NEC LCD4020-2-AV Specification preview
LCD4020-2-AV
Brand: NEC Pages: 6
NEC mPD75P308 Datasheet preview
mPD75P308
Brand: NEC Pages: 34

Brands by name

Popular brands

Load more brands