manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

Share
Download
Renesas SH7709S Hardware Manual Download Page 502

Rev. 5.00, 09/03, page 458 of 760

Initialization

Clear TE and RE bits in SCSCR to 0

Select communication

format in SCSMR

Set value in SCBRR

Set CKE1 and CKE0 bits in SCSCR

(TE and RE bits are 0)

Wait

Set TE and RE bits in SCSCR to 1

and set RIE, TIE, TEIE, and MPIE bits

Has a 1-bit 

interval elapsed?

End

No

Yes

(1)

(2)

(3)

(4)

Note:  Numbers in parentheses refer to steps in the preceding procedure description.

Figure 14.7   Sample Flowchart for SCI Initialization

Transmitting Serial Data (Asynchronous Mode): Figure 14.8 shows a sample flowchart for
transmitting serial data. The procedure for transmitting serial data is:

1. SCI status check and transmit data write: Read the serial status register (SCSSR), check that

the TDRE bit is 1, then write transmit data in the transmit data register (SCTDR) and clear
TDRE to 0.

2. To continue transmitting serial data: Read the TDRE bit to check whether it is safe to write (if

it reads 1); if so, write data in SCTDR, then clear TDRE to 0.

3. To output a break at the end of serial transmission: Set the port SC data register (SCPDR) and

port SC control register (SCPCR), then clear the TE bit to 0 in the serial control register
(SCSCR).  For SCPCR and SCPDR settings, see section 14.2.8, SC Port Control Register
(SCPCR)/SC Port Data Register (SCPDR).

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands