manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 66 of 760

31

16

11

12

17

0

Virtual address

Ways 0

−

3

VPN(31

−

17)

VPN(11

−

10)

ASID(7

−

0)

V

0

Address array

Data array

PPN(28

−

10) PR(1

−

0) SZ C

D SH

Index

31

Figure 3.7   TLB Indexing (IX = 0)

3.3.3

TLB Address Comparison

The results of address comparison determine whether a specific virtual page number is registered
in the TLB. The virtual page number of the virtual address that accesses external memory is
compared to the virtual page number of the indexed TLB entry. The ASID within the PTEH is
compared to the ASID of the indexed TLB entry. All four ways are searched simultaneously. If the
compared values match, and the indexed TLB entry is valid (V bit 

=

 1), the hit is registered.

It is necessary to have software ensure that TLB hits do not occur simultaneously in more than one
way, as hardware operation is not guaranteed if this occurs. For example, if there are two identical
TLB entries with the same VPN and a setting is made such that a TLB hit is made only by a
process with ASID = H'FF when one is in the shared state (SH = 1) and the other in the non-shared
state (SH = 0), then if the ASID in PTEH is set to H'FF, there is a possibility of simultaneous TLB
hits in both these ways. It is therefore necessary to ensure that this kind of setting is not made by
software.

The object compared varies depending on the page management information (SZ, SH) in the TLB
entry. It also varies depending on whether the system supports multiple virtual memory or single
virtual memory.

The page-size information determines whether VPN (11–10) is compared. VPN (11–10) is
compared for 1-kbyte pages (SZ = 0) but not for 4-kbyte pages (SZ = 1).

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Abus TVVR36500 User Manual preview
TVVR36500
Brand: Abus Pages: 60
mikroElektronika CAN SPI click Quick Start Manual preview
CAN SPI click
Brand: mikroElektronika Pages: 3
Cypress Semiconductor CY7C1019D Specification Sheet preview
CY7C1019D
Brand: Cypress Semiconductor Pages: 11
Altera Nios II Hardware Development Manual preview
Nios II
Brand: Altera Pages: 42
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
Paradyne Fan Tray 8820-S2-900 Installation Instructions Manual preview
Fan Tray 8820-S2-900
Brand: Paradyne Pages: 6
Xmart SNMP06 Reference Manual preview
SNMP06
Brand: Xmart Pages: 8
Belden HIRESCHMANN IT MAMMUTHUS MTM8003-FAN User Manual preview
HIRESCHMANN IT MAMMUTHUS MTM8003-FAN
Brand: Belden Pages: 84
OWC Mercury FireWire 400 Owner'S Manual preview
Mercury FireWire 400
Brand: OWC Pages: 2
ZALMAN RESERATOR1 V2 Installation And Operational Manual preview
RESERATOR1 V2
Brand: ZALMAN Pages: 18
R3 Bridge E User Manual preview
Bridge E
Brand: R3 Pages: 48
Boser HS-2605 Manual preview
HS-2605
Brand: Boser Pages: 82
VIA Technologies ARTiGO-A1200 Quick Manual preview
ARTiGO-A1200
Brand: VIA Technologies Pages: 2
Behringer MU-A043666 Quick Start Manual preview
MU-A043666
Brand: Behringer Pages: 12
Hama 62732 Operating Instructions Manual preview
62732
Brand: Hama Pages: 34
Epson S5U1C6F632T1 Hardware Manual preview
S5U1C6F632T1
Brand: Epson Pages: 48
Epson S5U1C63000H6 Manual preview
S5U1C63000H6
Brand: Epson Pages: 27
Epson S5U1C63007P Manual preview
S5U1C63007P
Brand: Epson Pages: 18

Brands by name

Popular brands

Load more brands