manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page xxxii of xliv

Figure 8.3

Manual Reset STATUS Output............................................................................ 193

Figure 8.4

Standby to Interrupt STATUS Output.................................................................. 194

Figure 8.5

Standby to Power-On Reset STATUS Output...................................................... 195

Figure 8.6

Standby to Manual Reset STATUS Output.......................................................... 196

Figure 8.7

Sleep to Interrupt STATUS Output ...................................................................... 196

Figure 8.8

Sleep to Power-On Reset STATUS Output.......................................................... 197

Figure 8.9

Sleep to Manual Reset STATUS Output .............................................................. 198

Figure 8.10

Hardware Standby Mode (When CA Goes Low in Normal Operation)............... 200

Figure 8.11

Hardware Standby Mode Timing (When CA Goes Low during WDT Operation
on Standby Mode Cancellation) ........................................................................... 201

Figure 9.1

Block Diagram of Clock Pulse Generator ............................................................ 204

Figure 9.2

Block Diagram of WDT ....................................................................................... 214

Figure 9.3

Writing to WTCNT and WTCSR......................................................................... 217

Figure 9.4

Points for Attention when Using Crystal Resonator............................................. 220

Figure 9.5

Points for Attention when Using PLL Oscillator Circuit ..................................... 221

Figure 10.1

Block Diagram of Bus State Controller................................................................ 225

Figure 10.2

Correspondence between Logical Address Space and Physical Address Space .. 229

Figure 10.3

Physical Space Allocation .................................................................................... 231

Figure 10.4

PCMCIA Space Allocation .................................................................................. 232

Figure 10.5

Writing to RFCR, RTCSR, RTCNT, and RTCOR............................................... 257

Figure 10.6

Basic Timing of Basic Interface ........................................................................... 269

Figure 10.7

Example of 32-Bit Data-Width Static RAM Connection ..................................... 270

Figure 10.8

Example of 16-Bit Data-Width Static RAM Connection ..................................... 271

Figure 10.9

Example of 8-Bit Data-Width Static RAM Connection ....................................... 272

Figure 10.10 Basic Interface Wait Timing (Software Wait Only) ............................................. 273
Figure 10.11 Basic Interface Wait State Timing (Wait State Insertion by 

WAIT

 Signal

WAITSEL = 1)..................................................................................................... 275

Figure 10.12 Example of 64-Mbit Synchronous DRAM Connection (32-Bit Bus Width)........ 277
Figure 10.13 Example of 64-Mbit Synchronous DRAM Connection (16-Bit Bus Width)........ 278
Figure 10.14 Basic Timing for Synchronous DRAM Burst Read ............................................. 282
Figure 10.15 Synchronous DRAM Burst Read Wait Specification Timing .............................. 283
Figure 10.16 Basic Timing for Synchronous DRAM Single Read............................................ 284
Figure 10.17 Basic Timing for Synchronous DRAM Burst Write ............................................ 286
Figure 10.18 Basic Timing for Synchronous DRAM Single Write........................................... 288
Figure 10.19 Burst Read Timing (No Precharge) ...................................................................... 291
Figure 10.20 Burst Read Timing (Same Row Address) ............................................................ 292
Figure 10.21 Burst Read Timing (Different Row Addresses) ................................................... 293
Figure 10.22 Burst Write Timing (No Precharge) ..................................................................... 294
Figure 10.23 Burst Write Timing (Same Row Address) ........................................................... 295
Figure 10.24 Burst Write Timing (Different Row Addresses) .................................................. 296
Figure 10.25 Auto-Refresh Operation ....................................................................................... 298
Figure 10.26 Synchronous DRAM Auto-Refresh Timing......................................................... 299
Figure 10.27 Synchronous DRAM Self-Refresh Timing .......................................................... 301

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 5
NEC Express5800/E120d-M Getting Started preview
Express5800/E120d-M
Brand: NEC Pages: 2
Opvimus UMX-ETH+ Operating Instructions Manual preview
UMX-ETH+
Brand: Opvimus Pages: 12
National Instruments NI-9252 Calibration Procedure preview
NI-9252
Brand: National Instruments Pages: 9
Analog Devices Linear SCP-LT8362-S-EVALZ Demo Manual preview
Linear SCP-LT8362-S-EVALZ
Brand: Analog Devices Pages: 8
Barco ImagePRO-HD Installation Manual preview
ImagePRO-HD
Brand: Barco Pages: 121
N.A.T. NAT-MCH Technical Reference Manual preview
NAT-MCH
Brand: N.A.T. Pages: 32
EKF Electronik CompactPCI CC8-BLUES User Manual preview
CompactPCI CC8-BLUES
Brand: EKF Electronik Pages: 52
Matrox Millennium P650 User Manual preview
Millennium P650
Brand: Matrox Pages: 54
Accom WSD/HDe Installation Procedure preview
WSD/HDe
Brand: Accom Pages: 15
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Brand: Z3 Technology Pages: 67
RANA Systems RanaSystems 13-0010--001 User Manual preview
RanaSystems 13-0010--001
Brand: RANA Systems Pages: 328
SYNTEK STA-UI-A0035 User Manual preview
STA-UI-A0035
Brand: SYNTEK Pages: 41
Rockwell Automation Trusted T8833 Manual preview
Trusted T8833
Brand: Rockwell Automation Pages: 21
DFRobot FIT0677 Assembly Manual preview
FIT0677
Brand: DFRobot Pages: 30
Comelit IPNVR016A User Manual preview
IPNVR016A
Brand: Comelit Pages: 140
ADLINK Technology aTCA-9710 User Manual preview
aTCA-9710
Brand: ADLINK Technology Pages: 86
Promax NGM EVO User Manual preview
NGM EVO
Brand: Promax Pages: 32

Brands by name

Popular brands

Load more brands