manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 304 of 760

10.3.5

Burst ROM Interface

Setting bits A0BST1–0, A5BST1–0, and A6BST1–0 in BCR1 to a non-zero value allows burst
ROM to be connected to areas 0, 5, and 6. The burst ROM interface provides high-speed access to
ROM that has a nibble access function. The timing for nibble access to burst ROM is shown in
figure 10.29. Two wait cycles are set. Basically, access is performed in the same way as for
normal space, but when the first cycle ends the 

CS0

 signal is not negated, and only the address is

changed before the next access is executed. When 8-bit ROM is connected, the number of
consecutive accesses can be set as 4, 8, or 16 by bits A0BST1–0, A5BST1–0, or A6BST1–0.
When 16-bit ROM is connected, 4 or 8 can be set in the same way. When 32-bit ROM is
connected, only 4 can be set.

WAIT

 pin sampling is performed in the first access if one or more wait states are set, and is

always performed in the second and subsequent accesses.

The second and subsequent access cycles also comprise two cycles when a burst ROM setting is
made and the wait specification is 0. The timing in this case is shown in figure 10.30.

However, the 

WAIT

 signal is ignored in the following three cases:

•

 

A write to external address space in dual address mode with 16-byte DMA transfer

•

 

Transfer from an external device with DACK to external address space in single address mode
with 16-byte DMA transfer

•

 

Cache write-back access

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

M-Audio Computer Quick Start Manual preview
Computer
Brand: M-Audio Pages: 10
Raritan DOMINION SX - Quick Setup Manual preview
DOMINION SX -
Brand: Raritan Pages: 4
TC Electronic ATAC Service Manual preview
ATAC
Brand: TC Electronic Pages: 55
Yaesu FT-817 - Modification Instructions preview
FT-817 -
Brand: Yaesu Pages: 2
3Ware 9550SX Series Installation Manual preview
9550SX Series
Brand: 3Ware Pages: 4
Parker PCH1 T P Series User Manual preview
PCH1 T P Series
Brand: Parker Pages: 107
ZALMAN Extreme Gaming VGA Cooler GV1000 User Manual preview
Extreme Gaming VGA Cooler GV1000
Brand: ZALMAN Pages: 7
QNAP Turbo NAS TVS-71 Series Hardware User Manual preview
Turbo NAS TVS-71 Series
Brand: QNAP Pages: 51
Longshine LCS-8170 User Manual preview
LCS-8170
Brand: Longshine Pages: 35
axing EOC 30-01 Quick Start Manual preview
EOC 30-01
Brand: axing Pages: 4
G&D DL-DVI-Vision-IP Series Installation And Operation Manual preview
DL-DVI-Vision-IP Series
Brand: G&D Pages: 228
Cypress Semiconductor CY62136EV30 MoBL Specification Sheet preview
CY62136EV30 MoBL
Brand: Cypress Semiconductor Pages: 12
Altera Stratix II User Manual preview
Stratix II
Brand: Altera Pages: 33
Dolby Laboratories Digital Loudspeaker Brochure preview
Digital Loudspeaker
Brand: Dolby Laboratories Pages: 4
Cypress Semiconductor CY7C68023 Specification Sheet preview
CY7C68023
Brand: Cypress Semiconductor Pages: 9
ZALMAN OPTIMA II CNPS10X User Manual preview
OPTIMA II CNPS10X
Brand: ZALMAN Pages: 20
Renesas Dummy IC M3T-SSOP36B-450 User Manual preview
Dummy IC M3T-SSOP36B-450
Brand: Renesas Pages: 4
Extron electronics Network Device PIP 444 User Manual preview
Network Device PIP 444
Brand: Extron electronics Pages: 62

Brands by name

Popular brands

Load more brands