manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 232 of 760

Shadow Space: Areas 0 and 2–6 are decoded by physical addresses A28–A26, which correspond
to areas 000 to 110. Address bits 31–29 are ignored. This means that the range of area 0 addresses,
for example, is H'00000000 to H'03FFFFFF, and its corresponding shadow space is the address
space obtained by adding to it H'20000000 

×

 n (n 

=

 1–6). The address range for area 7, which is

on-chip I/O space, is H'1C000000 to H'1FFFFFFF. The address space H'1C H'20000000

×

 n–H'1F H'20000000 

×

 n (n 

=

 0–7) corresponding to the area 7 shadow space is

reserved, and must not be used.

10.1.6

PCMCIA Support

The SH7709S supports PCMCIA standard interface specifications in physical space areas 5 and 6.

The interfaces supported are basically the “IC memory card interface” and “I/O card interface”
stipulated in JEIDA Specifications Ver. 4.2 (PCMCIA2.1).

Table 10.5

PCMCIA Interface Characteristics

Item

Feature

Access

Random access

Data bus

8/16 bits

Memory type

Mask ROM, OTPROM, EPROM, EEPROM, flash memory, SRAM

Memory capacity

Maximum 32 Mbytes

I/O space capacity

Maximum 32 Mbytes

Other features

Dynamic bus sizing of I/O bus width

*

The PCMCIA interface can be accessed from the address translation
area or non-address translation area.

Note:  

*

  Dynamic bus sizing of the I/O bus width is supported only in little-endian mode.

Common memory/Attribute memory

Area 5: H'14000000

Area 5: H'16000000

Common memory/Attribute memory

Area 6: H'18000000

I/O space

I/O space

Area 6: H'1A000000

Figure 10.4   PCMCIA Space Allocation

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

D-Link PCMCIA WIRELESS ASAPTER DWL-650 Quick Install Manual preview
PCMCIA WIRELESS ASAPTER DWL-650
Brand: D-Link Pages: 5
D-Link PowerLine DHP-W611AV User Manual preview
PowerLine DHP-W611AV
Brand: D-Link Pages: 78
IEI Technology HPE-4S1 Quick Installation Manual preview
HPE-4S1
Brand: IEI Technology Pages: 3
Seattle Computer Products 8086 CPU Instruction Manual preview
8086 CPU
Brand: Seattle Computer Products Pages: 31
Aqua Computer Aquaduct 360 XT Operating And Assembly Manual preview
Aquaduct 360 XT
Brand: Aqua Computer Pages: 28
ENERMAX ELC-LTTR240-TBP User Manual preview
ELC-LTTR240-TBP
Brand: ENERMAX Pages: 16
UfiSpace S9600-64X Hardware Installation Manual preview
S9600-64X
Brand: UfiSpace Pages: 35
Point of View SmartTV 210 User Manual preview
SmartTV 210
Brand: Point of View Pages: 13
Aaeon SBC-657B Manual preview
SBC-657B
Brand: Aaeon Pages: 61
IBM 2078-4F4 Quick Installation Manual preview
2078-4F4
Brand: IBM Pages: 130
2N Telekomunikace ATEUS STARGATE User Manual preview
ATEUS STARGATE
Brand: 2N Telekomunikace Pages: 67
IFM QHA200 Instructions For Setup preview
QHA200
Brand: IFM Pages: 12
Xilinx ML506 Quick Start Manual preview
ML506
Brand: Xilinx Pages: 29
Idis DR-8364F Quick Manual preview
DR-8364F
Brand: Idis Pages: 16
NXP Semiconductors RDGD3160I3PH5EVB User Manual preview
RDGD3160I3PH5EVB
Brand: NXP Semiconductors Pages: 21
Lanner NCA-6520 User Manual preview
NCA-6520
Brand: Lanner Pages: 141
Renesas RL78/L1C User Manual preview
RL78/L1C
Brand: Renesas Pages: 4
H3C SecPath L5030 Installation Manual preview
SecPath L5030
Brand: H3C Pages: 62

Brands by name

Popular brands

Load more brands