Renesas SH7709S Hardware Manual Download Page 217 | Manualshive

Page: 217 / 807

background image

Rev. 5.00, 09/03, page 173 of 760

7.3.6

PC Trace

1. Setting PCTE in BRCR to 1 enables PC traces. When branch (branch instruction, repeat, and

interrupt) is generated, the address from which the branch source address can be calculated and
the branch destination address are stored in BRSR and BRDR, respectively. The branch
address and the pointer, which corresponds to the branch, are included in BRSR.

2. The branch address before branch occurs can be calculated from the address and the pointer

stored in BRSR. The expression from BSA (the address in BRSR), PID (the pointer in BRSR),
and IA (the instruction address before branch occurs) is as follows: IA = BSA – 2 * PID.

Notes are needed when an interrupt (a branch) is issued before the branch destination
instruction is executed. In case of the next figure, the instruction “Exec” executed immediately
before branch is calculated by IA = BSA – 2 * PID. However, when branch “branch” has delay
slot and the destination address is 4n + 2 address, the address “Dest” which is specified by
branch instruction is stored in BRSR (Dest = BSA). Therefore, as IA = BSA – 2 * PID is not
applied to this case, this PID is invalid. The case where BSA is 4n + 2 boundary is applied
only to this case and then some cases are classified as follows:

Exec:branch

Dest

Dest:instr

(not executed)

interrupt

Int: interrupt routine

If the PID value is odd, instruction buffer indicates PID+2 buffer. However, these expressions
in this table are accounted for it. Therefore, the true branch source address is calculated with
BSA and PID values stored in BRSR.

3. The branch address before branch occurrence, IA, has different values due to some kinds of

branch.

a. Branch instruction

The branch instruction address

b. Interrupt

The last instruction executed before interrupt

The top address of interrupt routine is stored in BRDR.

4. BRSR and BRDR have eight pairs of queue structures. The top of queues is read first when the

address stored in the PC trace register is read. BRSR and BRDR share the read pointer. Read
BRSR and BRDR in order, the queue only shifts after BRDR is read. When reading BRDR,
longword access should be used. Also, the PC trace has a trace pointer, which initially points
to the bottom of the queues. The first pair of branch addresses will be stored at the bottom of
the queues, then push up when next pairs come into the queues. The trace pointer will points to
the next branch address to be executed, unless it got push out of the queues. When the branch
address has been executed, the trace pointer will shift down to next pair of addresses, until it

«
...
215
216
217
218
219
...
»

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Brand: Patton electronics Pages: 16

SCSI PC Card REX-9530V

Brand: Ratoc Systems Pages: 30

Brand: Yaesu Pages: 2

Brand: Paradyne Pages: 1

Brand: Edge-Core Pages: 7

Brand: Zonet Pages: 2

Brand: ICP DAS USA Pages: 8

Brand: Uniden Pages: 5

Brand: Paradyne Pages: 6

Brand: Harman Pages: 24

Brand: Dave Embedded Systems Pages: 79

Brand: ELSA Pages: 60

Brand: Helmholz Pages: 14

Symphonique Strings SRX-04

Brand: Roland Pages: 12

USB device 622x

Brand: National Instruments Pages: 23

Brand: Black Box Pages: 1

Brand: ekwb Pages: 36

Brand: COMBA Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands