manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 540 of 760

Initialization

Clear TE and RE bits in SCSCR to 0

Set TFRST and RFRST bits in

SCFCR to 1

1-bit interval elapsed?

Set RTRG1-0, TTRG1-0, and MCE 

in SCFCR

Clear TFRST and RFRST bits to 0

Set TE and RE bits in 

SCSCR to 1,and set RIE, TIE, 

TEIE, and MPIE bits

Set communication format in SCSMR

Yes

No

Set value in SCBRR

Set CKE1 and CKE0 

bits in SCSCR (leaving TE and RE 

bits cleared to 0)

End

(1) 

(2) 

(3) 

(4) 

Wait

Note:  Numbers in parentheses refer to steps in the preceding procedure description.

Figure 16.5   Sample Flowchart for SCIF Initialization

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual preview
AirPlus XtremeG Ethernet-to-Wireless Bridge...
Brand: D-Link Pages: 31
Ebyte E103-W13 User Manual preview
E103-W13
Brand: Ebyte Pages: 14
ESD ECS-CPCIs/FPGA Hardware Manual preview
ECS-CPCIs/FPGA
Brand: ESD Pages: 28
Endace DAG 7.1S User Manual preview
DAG 7.1S
Brand: Endace Pages: 51
Bridgeworks Oresund EFC102200 User Manual preview
Oresund EFC102200
Brand: Bridgeworks Pages: 84
XJTAG XJLink2-CFM User Manual preview
XJLink2-CFM
Brand: XJTAG Pages: 9
Xilinx Zynq-7000 Manual preview
Zynq-7000
Brand: Xilinx Pages: 8
DCB BROADCAST POLLING FRAD BPF-14 BU Manual preview
BROADCAST POLLING FRAD BPF-14 BU
Brand: DCB Pages: 28
ekwb EK-FC750 GTX Series Installation Manual preview
EK-FC750 GTX Series
Brand: ekwb Pages: 2
ZiLOG Z8 GP ZGP323 User Manual preview
Z8 GP ZGP323
Brand: ZiLOG Pages: 11
Altera Stratix II User Manual preview
Stratix II
Brand: Altera Pages: 33
Keysight Technologies U3024AH10 User'S And Service Manual preview
U3024AH10
Brand: Keysight Technologies Pages: 106
Aaeon GENE-EHL7 User Manual preview
GENE-EHL7
Brand: Aaeon Pages: 119
Aleratec 260206 Quick Start Manual preview
260206
Brand: Aleratec Pages: 16
Hologic ThinPrep 3000 Operator'S Manual preview
ThinPrep 3000
Brand: Hologic Pages: 256
TECO e-chill 1 Instruction Manual preview
e-chill 1
Brand: TECO Pages: 24
Delta Electronics Suppression Inductors LFZ24H Specification Sheet preview
Suppression Inductors LFZ24H
Brand: Delta Electronics Pages: 1
Dahua Technology NVR52A16-16P-4KS2 Quick Start Manual preview
NVR52A16-16P-4KS2
Brand: Dahua Technology Pages: 13

Brands by name

Popular brands

Load more brands