manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 403 of 760

•

 

External Clock Operation: Set the TPSC2–TPSC0 bits in TCR to select the external clock
(TCLK) as the timer clock. Use the CKEG1 and CKEG0 bits in TCR to select the detection
edge. Rising, falling, or both edges may be selected. The pulse width of the external clock
must be at least 1.5 peripheral module clock cycles for single edges or 2.5 peripheral module
clock cycles for both edges. A shorter pulse width will result in accurate operation. Figure 12.5
shows the timing for both-edge detection.

P

φ

External

clock input

pin (TCLK)

TCNT

 input clock

TCNT

N + 1

N

N 

−

 1

Figure 12.5   Count Timing when Operating on External Clock (Both Edges Detected)

•

 

On-Chip RTC Clock Operation: Set the TPSC2–TPSC0 bits in TCR to select the on-chip RTC
clock as the timer clock. Figure 12.6 shows the timing.

RTC output

clock

TCNT

TCNT input

clock

N + 1

N

N 

−

 1

Figure 12.6   Count Timing when Operating on On-Chip RTC Clock

12.3.2

Input Capture Function

Channel 2 has an input capture function (figure 12.7). When using the input capture function, set
the TCLK pin to input mode with the TCOE bit in the timer output control register (TOCR) and
set the timer operation clock to internal clock or on-chip RTC clock with the TPCS2–TPCS0 bits
in the timer control register (TCR2). Also, designate use of the input capture function and whether
to generate interrupts on input capture with the IPCE1–IPCE0 bits in TCR2, and designate the use
of either the rising or falling edge of the TCLK pin to set the timer counter (TCNT2) value into the
input capture register (TCPR2) with the CKEG1–CKEG0 bits in TCR2.

The input capture function cannot be used in standby mode.

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

PACOM Professional Series Quick Manual preview
Professional Series
Brand: PACOM Pages: 15
Rane CP 31 Datasheet preview
CP 31
Brand: Rane Pages: 4
Teagle Tomahawk 7100 Operator'S Manual preview
Tomahawk 7100
Brand: Teagle Pages: 40
FS FS-BOX-V3 Quick Start Manual preview
FS-BOX-V3
Brand: FS Pages: 19
Supermicro SAS-827HD User Manual preview
SAS-827HD
Brand: Supermicro Pages: 16
EVOC 6336-STG-YX Manual preview
6336-STG-YX
Brand: EVOC Pages: 57
Optostar OP-8000-EDFA-1U Series Manual preview
OP-8000-EDFA-1U Series
Brand: Optostar Pages: 9
ZALMAN ZM-MFC1 Combo User Manual preview
ZM-MFC1 Combo
Brand: ZALMAN Pages: 7
CompuLab CL-SOM-AM57 Series Reference Manual preview
CL-SOM-AM57 Series
Brand: CompuLab Pages: 79
Renesas M34502T-MCU User Manual preview
M34502T-MCU
Brand: Renesas Pages: 40
National Instruments IMAQTM User Manual preview
IMAQTM
Brand: National Instruments Pages: 121
ICP ICP9014RO Installation And User Manual preview
ICP9014RO
Brand: ICP Pages: 142
Lantronix N-FXE 02B Series User Manual preview
N-FXE 02B Series
Brand: Lantronix Pages: 10
Moxa Technologies Smartio CP-104UL Quick Installation Manual preview
Smartio CP-104UL
Brand: Moxa Technologies Pages: 2
ST METERS AND MORE UM2241 User Manual preview
METERS AND MORE UM2241
Brand: ST Pages: 26
ACTi GNR-410 Quick Installation Manual preview
GNR-410
Brand: ACTi Pages: 12
Quatech SSPX-100 User Manual preview
SSPX-100
Brand: Quatech Pages: 5
NETGEAR ReadyNAS Duo v2 Software Manual preview
ReadyNAS Duo v2
Brand: NETGEAR Pages: 100

Brands by name

Popular brands

Load more brands