manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 327 of 760

Section 11   Direct Memory Access Controller (DMAC)

11.1

Overview

The SH7709S includes a four-channel direct memory access controller (DMAC). The DMAC can
be used in place of the CPU to perform high-speed transfers between external devices that have
DACK (transfer request acknowledge signal), external memory, memory-mapped external
devices, and on-chip peripheral modules (IrDA, SCIF, A/D converter, and D/A converter). Using
the DMAC reduces the burden on the CPU and increases overall operating efficiency.

11.1.1

Features

The DMAC has the following features.

•

 

Four channels

•

 

4-GB address space in the architecture

•

 

16-byte transfer (In 16-byte transfer, four 32-bit reads are executed, followed by four 32-bit
writes.)

•

 

Choice of 8-bit, 16-bit, 32-bit, or 16-byte transfer data length

•

 

16 Mbytes (16,777,216 transfers)

•

 

Address mode: Dual address mode and single address mode are supported.  In addition, direct
address transfer mode or indirect address transfer mode can be selected.

 

Dual address mode transfer: Both the transfer source and transfer destination are accessed
by address. Dual address mode has direct address transfer mode and indirect address
transfer mode.

Direct address transfer mode:  The values specified in the DMAC registers indicates the
transfer source and transfer destination.  Two bus cycles are required for one data transfer.

Indirect address transfer mode:  Data is transferred with the address stored prior to the
address specified in the transfer source address in the DMAC.  Other operations are the
same as those of direct address transfer mode.  This function is only available in channel 3.
Four bus cycles are required for one data transfer.

 

Single address mode transfer: Either the transfer source or transfer destination peripheral
device is accessed (selected) by means of the DACK signal, and the other device is
accessed by address. One transfer unit of data is transferred in one bus cycle.

•

 

Channel functions: The transfer mode that can be specified depends on the channel:

 

Channel 0: External request can be accepted.

 

Channel 1: External request can be accepted.

 

Channel 2: This channel has a source address reload function, which reloads a source
address every four transfers.

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

ekwb EK-Vector Radeon RX5700 + XT Backplate Installation Manual preview
EK-Vector Radeon RX5700 + XT Backplate
Brand: ekwb Pages: 7
AXIOMTEK eBOX532-100-FL Series Quick Installation Manual preview
eBOX532-100-FL Series
Brand: AXIOMTEK Pages: 2
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
Dahua D-NVR4108HS-4KS2/L Quick Start Manual preview
D-NVR4108HS-4KS2/L
Brand: Dahua Pages: 33
B&B Electronics PCMCIA High Speed Serial Card CE 232HSPCC User Manual preview
PCMCIA High Speed Serial Card CE 232HSPCC
Brand: B&B Electronics Pages: 14
Altera Stratix II User Manual preview
Stratix II
Brand: Altera Pages: 33
TDK Powereta iQP Series Product Brief preview
Powereta iQP Series
Brand: TDK Pages: 2
Digi 9P 9360/9750 User Manual preview
9P 9360/9750
Brand: Digi Pages: 75
Optus Ultra WiFi Booster Quick Manual preview
Ultra WiFi Booster
Brand: Optus Pages: 8
Mod Duo X User Manual preview
Duo X
Brand: Mod Pages: 11
OWC ACCELSIOR 8M2 Assembly Manual & User Manual preview
ACCELSIOR 8M2
Brand: OWC Pages: 9
Kontron KISS Stor Slim Quick Installation Manual preview
KISS Stor Slim
Brand: Kontron Pages: 4
Ecolab EcoJet EcoStar 1500 Installation & Operation Manual preview
EcoJet EcoStar 1500
Brand: Ecolab Pages: 80
Advantech ASMB-816 Series User Manual preview
ASMB-816 Series
Brand: Advantech Pages: 110
Advantech ASMB-610 User Manual preview
ASMB-610
Brand: Advantech Pages: 126
D-Link Express EtherNetwork DFE-670TXD Specifications preview
Express EtherNetwork DFE-670TXD
Brand: D-Link Pages: 2
Hitachi AP1 Data Book preview
AP1
Brand: Hitachi Pages: 378

Brands by name

Popular brands

Load more brands