manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 315 of 760

I/O Card Interface Timing: Figures 10.37 and 10.38 show the timing for the PCMCIA I/O card
interface.

Switching between the I/O card interface and the IC memory card interface is performed
according to the accessed address. When PCMCIA is designed for physical space area 5, the bus
access is automatically performed as an I/O card interface access when a physical address from
H'16000000 to H'17FFFFFF is accessed. When PCMCIA is designated for physical space area 6,
the bus access is automatically performed as an I/O card interface access when a physical address
from H'1A000000 to H'1BFFFFFF is accessed.

When accessing a PCMCIA I/O card, the access should be performed using a non-cacheable area
in virtual space (P2 or P3 space) or an area specified as non-cacheable by the MMU.

When an I/O card interface access is made to a PCMCIA card in little-endian mode, dynamic
sizing of the I/O bus width is possible using the 

IOIS16

 pin. When a 16-bit bus width is set for are

5 or area 6, if the 

IOIS16

 signal is high during a word-size I/O bus cycle, the I/O port is

recognized as being 8 bits in width. In this case, a data access for only 8 bits is performed in the
I/O bus cycle being executed, followed automatically by a data access for the remaining 8 bits.

Figure 10.39 shows the basic timing for dynamic bus sizing.

In big-endian mode, the 

IOIS16 

signal is not supported, and should be fixed low.

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

3Com 3CRWB6096 Quick Start Manual preview
3CRWB6096
Brand: 3Com Pages: 8
Data Translation DT330 Series Getting Started Manual preview
DT330 Series
Brand: Data Translation Pages: 60
Hama 39707 Operating Instruction preview
39707
Brand: Hama Pages: 4
ekwb EK-FC1080 GTX Ti TF6 Installation Manual preview
EK-FC1080 GTX Ti TF6
Brand: ekwb Pages: 2
Moxa Technologies UC-8100 Series Hardware User Manual preview
UC-8100 Series
Brand: Moxa Technologies Pages: 19
IDT DBP 7+4 User Manual preview
DBP 7+4
Brand: IDT Pages: 93
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Brand: UNA AUTOMATION Pages: 20
Paradyne Fan Tray 8820-S2-900 Installation Instructions Manual preview
Fan Tray 8820-S2-900
Brand: Paradyne Pages: 6
Xmart SNMP06 Reference Manual preview
SNMP06
Brand: Xmart Pages: 8
3Com 3C433279A Release Note preview
3C433279A
Brand: 3Com Pages: 12
Aaeon FWS-7150 Manual preview
FWS-7150
Brand: Aaeon Pages: 57
Juniper NSM4000 Hardware Manual preview
NSM4000
Brand: Juniper Pages: 196
Omron F3SP-U3P-TGR User Manual preview
F3SP-U3P-TGR
Brand: Omron Pages: 29
ICP ICP9014RO Installation And User Manual preview
ICP9014RO
Brand: ICP Pages: 142
Xcellon DRD-501 User Manual preview
DRD-501
Brand: Xcellon Pages: 24
Homeworks HQP7-RF-2 Installation Instructions Manual preview
HQP7-RF-2
Brand: Homeworks Pages: 24
LevelOne FSW-0512 Specification Sheet preview
FSW-0512
Brand: LevelOne Pages: 2
ekwb EK-UNI Holder D5 V3 Installation And Mounting Manual preview
EK-UNI Holder D5 V3
Brand: ekwb Pages: 2

Brands by name

Popular brands

Load more brands