manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page xxiii of xliv

11.1.1 Features ................................................................................................................ 327
11.1.2 Block Diagram ..................................................................................................... 329
11.1.3 Pin Configuration ................................................................................................. 330
11.1.4 Register Configuration ......................................................................................... 331

11.2

Register Descriptions......................................................................................................... 333
11.2.1 DMA Source Address Registers 0–3 (SAR0–SAR3)........................................... 333
11.2.2 DMA Destination Address Registers 0–3 (DAR0–DAR3) .................................. 334
11.2.3 DMA Transfer Count Registers 0–3 (DMATCR0–DMATCR3) ......................... 335
11.2.4 DMA Channel Control Registers 0–3 (CHCR0–CHCR3) ................................... 336
11.2.5 DMA Operation Register (DMAOR) ................................................................... 343

11.3

Operation ........................................................................................................................... 345
11.3.1 DMA Transfer Flow............................................................................................. 345
11.3.2 DMA Transfer Requests....................................................................................... 347
11.3.3 Channel Priority ................................................................................................... 349
11.3.4 DMA Transfer Types ........................................................................................... 352
11.3.5 Number of Bus Cycle States and 

DREQ

 Pin Sampling Timing ........................... 363

11.3.6 Source Address Reload Function ......................................................................... 372
11.3.7 DMA Transfer Ending Conditions ....................................................................... 374

11.4

Compare Match Timer (CMT) .......................................................................................... 376
11.4.1 Overview .............................................................................................................. 376
11.4.2 Register Descriptions ........................................................................................... 377
11.4.3 Operation.............................................................................................................. 380
11.4.4 Compare Match .................................................................................................... 381

11.5

Examples of Use................................................................................................................ 383
11.5.1 Example of DMA Transfer between On-Chip IrDA and External Memory ........ 383
11.5.2 Example of DMA Transfer between A/D Converter and External Memory ........ 384
11.5.3 Example of DMA Transfer between External Memory and SCIF Transmitter

(Indirect Address On) ........................................................................................... 385

11.6

Usage Notes....................................................................................................................... 387

Section 12   Timer (TMU)

................................................................................................... 389

12.1

Overview ........................................................................................................................... 389
12.1.1 Features ................................................................................................................ 389
12.1.2 Block Diagram ..................................................................................................... 390
12.1.3 Pin Configuration ................................................................................................. 391
12.1.4 Register Configuration ......................................................................................... 391

12.2

TMU Registers .................................................................................................................. 392
12.2.1 Timer Output Control Register (TOCR) .............................................................. 392
12.2.2 Timer Start Register (TSTR)................................................................................ 392
12.2.3 Timer Control Registers (TCR)............................................................................ 393
12.2.4 Timer Constant Registers (TCOR) ....................................................................... 397
12.2.5 Timer Counters (TCNT)....................................................................................... 397
12.2.6 Input Capture Register (TCPR2) .......................................................................... 399

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

AlphaShield INTERNET PRIVACY PROTECTION (Spanish) Manual Del Usuario preview
INTERNET PRIVACY PROTECTION
Brand: AlphaShield Pages: 49
Accusys ACS-76500 Owner'S Manual preview
ACS-76500
Brand: Accusys Pages: 34
ekwb EK-FB GA AX370 Gaming RGB Monoblock Installation Manual preview
EK-FB GA AX370 Gaming RGB Monoblock
Brand: ekwb Pages: 2
IAR SYSTEMS IAR KickStart Kit TWR-K60N512-IAR Getting Started Manual preview
IAR KickStart Kit TWR-K60N512-IAR
Brand: IAR SYSTEMS Pages: 8
LSI MegaRAID SATA 300-4XLP Quick Installation Manual preview
MegaRAID SATA 300-4XLP
Brand: LSI Pages: 3
8e6 Technologies ER3-100 (5K02-55) Quick Start Manual preview
ER3-100 (5K02-55)
Brand: 8e6 Technologies Pages: 74
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Brand: Lutron Electronics Pages: 4
Crystal Vision TANDEM HD-21 User Manual preview
TANDEM HD-21
Brand: Crystal Vision Pages: 54
Riverbed SteelCentral AppResponse 2180 Upgrade And Maintenance Manual preview
SteelCentral AppResponse 2180
Brand: Riverbed Pages: 82
MICROENER IM30-CV Operation Manual preview
IM30-CV
Brand: MICROENER Pages: 24
ekwb EK-FC750 GTX Series Installation Manual preview
EK-FC750 GTX Series
Brand: ekwb Pages: 2
ZALMAN CNPS20X User Manual preview
CNPS20X
Brand: ZALMAN Pages: 20
ADLINK Technology AMSTX-CF Series User Manual preview
AMSTX-CF Series
Brand: ADLINK Technology Pages: 73
Aaeon FWS-7811 Manual preview
FWS-7811
Brand: Aaeon Pages: 100
Azoteq IQ Switch ProxSense RS100 Application Notes preview
IQ Switch ProxSense RS100
Brand: Azoteq Pages: 9
IEI Technology PUZZLE-5030 User Manual preview
PUZZLE-5030
Brand: IEI Technology Pages: 119
B&B Electronics ESR901 User Manual preview
ESR901
Brand: B&B Electronics Pages: 90
TL Audio IVORY 2 5052 User Manual preview
IVORY 2 5052
Brand: TL Audio Pages: 37

Brands by name

Popular brands

Load more brands