manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 167 of 760

7.2.11

Branch Source Register (BRSR)

BRSR is a 32-bit read register. BRSR stores the last fetched address before branch and the pointer
(3 bits) which indicates the number of cycles from fetch to execution for the last executed
instruction. BRSR has the flag bit that is set to 1 when branch occurs. This flag bit is cleared to 0,
when BRSR is read and also initialized by power-on resets or manual resets. Other bits are not
initialized by reset. Eight BRSR registers have queue structure and a stored register is shifted
every branch.

Bit:

31

30

29

28

27

26

25

24

SVF

PID2

PID1

PID0

BSA27

BSA26

BSA25

BSA24

Initial value:

0

*

*

*

*

*

*

*

R/W:

R

R

R

R

R

R

R

R

Bit:

23

22

21

20

19

18

17

16

BSA23

BSA22

BSA21

BSA20

BSA19

BSA18

BSA17

BSA16

Initial value:

*

*

*

*

*

*

*

*

R/W:

R

R

R

R

R

R

R

R

Bit:

15

14

13

12

11

10

9

8

BSA15

BSA14

BSA13

BSA12

BSA11

BSA10

BSA9

BSA8

Initial value:

*

*

*

*

*

*

*

*

R/W:

R

R

R

R

R

R

R

R

Bit:

7

6

5

4

3

2

1

0

BSA7

BSA6

BSA5

BSA4

BSA3

BSA2

BSA1

BSA0

Initial value:

*

*

*

*

*

*

*

*

R/W:

R

R

R

R

R

R

R

R

Note:  

*

  Undefined value

Bit 31—BRSR Valid Flag (SVF): Indicates whether the address and the pointer by which the
branch source address can be calculated. When a branch source address is fetched, this flag is set
to 1. This flag is cleared to 0 in reading BRSR.

Bit 31: SVF

Description

0

The value of BRSR register is invalid

1

The value of BRSR register is valid

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Paradyne 4300 Installation Instructions Manual preview
4300
Brand: Paradyne Pages: 22
National Instruments USB-6501 Quick Start preview
USB-6501
Brand: National Instruments Pages: 5
National Instruments PXIe-8106 User Manual preview
PXIe-8106
Brand: National Instruments Pages: 76
Vivotek NR8401 User Manual preview
NR8401
Brand: Vivotek Pages: 136
Western Digital Scorpio WD2500BPVT Product Specifications preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 3
Western Digital Scorpio WD2500BPVT Product Features preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 4
Tandberg Data Storagelibrary T24 Manual preview
Storagelibrary T24
Brand: Tandberg Data Pages: 28
IBM EtherLink XL User Manual preview
EtherLink XL
Brand: IBM Pages: 72
AXIOMTEK FAB118-14B5P7 Quick Installation Manual preview
FAB118-14B5P7
Brand: AXIOMTEK Pages: 2
Magewell XI100DUSB-SDI User Manual preview
XI100DUSB-SDI
Brand: Magewell Pages: 10
Z3 Technology Z3-HE2160-RPS User Instructions preview
Z3-HE2160-RPS
Brand: Z3 Technology Pages: 18
Keithley 7075 Instruction Manual preview
7075
Brand: Keithley Pages: 108
Idis DR-8516 Installation Manual preview
DR-8516
Brand: Idis Pages: 28
BSS Audio Soundweb 9088ii DSP System    Brochure & Specs preview
Soundweb 9088ii DSP System   
Brand: BSS Audio Pages: 2
IBM Nways 2216 Service And Maintenance Manual preview
Nways 2216
Brand: IBM Pages: 168
Forcepoint V10000 G4R2 Quick Start Manual preview
V10000 G4R2
Brand: Forcepoint Pages: 2
Me VS-M1 Instructions Manual preview
VS-M1
Brand: Me Pages: 28
G&D DP1.2-Vision-IP-Fiber Installation And Operation Manual preview
DP1.2-Vision-IP-Fiber
Brand: G&D Pages: 240

Brands by name

Popular brands

Load more brands