manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 486 of 760

TEND Flag and TE Bit Processing: The TEND flag is set to 1 during transmission of the stop bit
of the last data.  Consequently, if the TE bit is cleared to 0 immediately after setting of the TEND
flag has been confirmed, the stop bit will be in the process of transmission and will not be
transmitted normally.  Therefore, the TE bit should not be cleared to 0 for at least 0.5 serial clock
cycles (or 1.5 cycles if two stop bits are used) after setting of the TEND flag is confirmed.

Receive Error Flags and Transmitter Operation (Synchronous Mode Only): When a receive
error flag (ORER, PER, or FER) is set to 1, the SCI will not start transmitting even if TDRE is set
to 1. Be sure to clear the receive error flags to 0 before starting to transmit. Note that clearing RE
to 0 does not clear the receive error flags.

Receive Data Sampling Timing and Receive Margin in Asynchronous Mode: In asynchronous
mode, the SCI operates on a base clock of 16 times the transfer rate frequency. In receiving, the
SCI synchronizes internally with the falling edge of the start bit, which it samples on the base
clock. Receive data is latched at the rising edge of the eighth base clock pulse (figure 14.24).

0 1 2 3 4 5 6 7 8 9 10111213 1415 0 1 2 3 4 5 6 7 8 9 10111213 1415 0 1 2 3 4 5

Base clock

Receive

data (RxD)

Synchro-

nization

sampling

timing

Data

sampling

timing

8 clocks

16 clocks

Start bit

−

7.5 clocks

+7.5 clocks

D0

D1

Figure 14.24   Receive Data Sampling Timing in Asynchronous Mode

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Amperes iPX5500 Instruction Manual preview
iPX5500
Brand: Amperes Pages: 8
IDT TSI384 User Manual preview
TSI384
Brand: IDT Pages: 281
DMX4ALL DMX-Universal-Demux User Manual preview
DMX-Universal-Demux
Brand: DMX4ALL Pages: 17
Rockwell Automation 41LR4060 Instruction Manual preview
41LR4060
Brand: Rockwell Automation Pages: 108
Qlogic QMC2462S Datasheet preview
QMC2462S
Brand: Qlogic Pages: 2
B&B Electronics Parallel & Serial Port Checker PPC User Manual preview
Parallel & Serial Port Checker PPC
Brand: B&B Electronics Pages: 4
Balluff BIC 1I12-P2A25-M30MI1-BPX05-110 User Manual preview
BIC 1I12-P2A25-M30MI1-BPX05-110
Brand: Balluff Pages: 12
S&T kontron KBox E-420-R1K/V1K User Manual preview
kontron KBox E-420-R1K/V1K
Brand: S&T Pages: 82
MC PCIe-DIO96H User Manual preview
PCIe-DIO96H
Brand: MC Pages: 21
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Brand: Softing Pages: 4
Lanner NCA-1525 User Manual preview
NCA-1525
Brand: Lanner Pages: 78
Z3 Technology SBE264-10-RPS User Instructions preview
SBE264-10-RPS
Brand: Z3 Technology Pages: 87
Uniden Data 2000 Manual preview
Data 2000
Brand: Uniden Pages: 5
IBM Power System H924 Installing Instructions preview
Power System H924
Brand: IBM Pages: 48
ADTRAN EXPRESS 6503 User Manual preview
EXPRESS 6503
Brand: ADTRAN Pages: 20
Renesas RL78/L1C User Manual preview
RL78/L1C
Brand: Renesas Pages: 4
Allied Telesis AR440S Hardware Reference Manual preview
AR440S
Brand: Allied Telesis Pages: 44
Agilent Technologies 72B Command Reference Manual preview
72B
Brand: Agilent Technologies Pages: 458

Brands by name

Popular brands

Load more brands