manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page xl of xliv

Table 8.2

Pin Configuration.................................................................................................... 183

Table 8.3

Register Configuration............................................................................................ 183

Table 8.4

Register States in Standby Mode ............................................................................ 188

Table 9.1

CPG Pins and Functions ......................................................................................... 206

Table 9.2

CPG Register .......................................................................................................... 206

Table 9.3

Clock Operating Modes .......................................................................................... 207

Table 9.4

Available Combinations of Clock Mode and FRQCR Values................................ 208

Table 9.5

Register Configuration............................................................................................ 214

Table 10.1

BSC Pins................................................................................................................. 226

Table 10.2

BSC Registers......................................................................................................... 228

Table 10.3

Physical Address Space Map .................................................................................. 230

Table 10.4

Correspondence between External Pins (MD4 and MD3) and Memory Size......... 231

Table 10.5

PCMCIA Interface Characteristics ......................................................................... 232

Table 10.6

PCMCIA Support Interface .................................................................................... 233

Table 10.7

32-Bit External Device/Big-Endian Access and Data Alignment .......................... 260

Table 10.8

16-Bit External Device/Big-Endian Access and Data Alignment .......................... 261

Table 10.9

8-Bit External Device/Big-Endian Access and Data Alignment ............................ 262

Table 10.10 32-Bit External Device/Little-Endian Access and Data Alignment........................ 263
Table 10.11 16-Bit External Device/Little-Endian Access and Data Alignment........................ 263
Table 10.12 8-Bit External Device/Little-Endian Access and Data Alignment.......................... 264
Table 10.13 Relationship between Bus Width, AMX Bits, and Address Multiplex Output ....... 279
Table 10.14 Example of Correspondence between SH7709S and Synchronous DRAM

Address Pins (AMX [3:0] = 0100 (32-Bit Bus Width)).......................................... 281

Table 10.15 MCSCRx Settings and 

MCS[x]

 Assertion Conditions (x: 0–7).............................. 324

Table 11.1

DMAC Pins ............................................................................................................ 330

Table 11.2

DMAC Registers .................................................................................................... 331

Table 11.3

Selecting External Request Modes with RS Bits .................................................... 347

Table 11.4

Selecting On-Chip Peripheral Module Request Modes with RS3-0 Bits................ 348

Table 11.5

Supported DMA Transfers...................................................................................... 352

Table 11.6

Relationship between Request Modes and Bus Modes by DMA Transfer
Category ................................................................................................................. 361

Table 11.7

Register Configuration............................................................................................ 377

Table 11.8

Transfer Conditions and Register Settings for Transfer between On-Chip SCI
and External Memory ............................................................................................. 383

Table 11.9

Transfer Conditions and Register Settings for Transfer between On-Chip A/D
Converter and External Memory ............................................................................ 384

Table 11.10 Values in DMAC after End of Fourth Transfer ...................................................... 385
Table 11.11 Transfer Conditions and Register Settings for Transfer between External

Memory and SCIF Transmitter............................................................................... 386

Table 12.1

TMU Pin ................................................................................................................. 391

Table 12.2

TMU Registers........................................................................................................ 391

Table 12.3

TMU Interrupt Sources........................................................................................... 405

Table 13.1

RTC Pins................................................................................................................. 409

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
EAW MX250 Owner'S Manual preview
MX250
Brand: EAW Pages: 10
GE MDS SD Series Setup Manual preview
MDS SD Series
Brand: GE Pages: 4
Lauterbach C2000 Manual preview
C2000
Brand: Lauterbach Pages: 61
NEC Univerge SV9300 Migration Manual preview
Univerge SV9300
Brand: NEC Pages: 26
NEC NEAX 2400 Quick Reference Manual preview
NEAX 2400
Brand: NEC Pages: 20
NEC DS2000 IntraMail Instructions preview
DS2000 IntraMail
Brand: NEC Pages: 2
National Instruments NI 9203 User Manual And Specifications preview
NI 9203
Brand: National Instruments Pages: 85
iWave iW-RainboW-G30D Hardware User'S Manual preview
iW-RainboW-G30D
Brand: iWave Pages: 89
Intel SRCSASBB8I - RAID Controller Hardware User'S Manual preview
SRCSASBB8I - RAID Controller
Brand: Intel Pages: 36
ADC HiGain HLU-231 List 8F Quick Installation preview
HiGain HLU-231 List 8F
Brand: ADC Pages: 7
AYRSTONE AyrMesh IndoorAP Instructions preview
AyrMesh IndoorAP
Brand: AYRSTONE Pages: 2
Grundig GSS STC 160 Assembly Instruction Manual preview
GSS STC 160
Brand: Grundig Pages: 24
TDK InvenSense RoboKit1 Hardware Reference Manual preview
InvenSense RoboKit1
Brand: TDK Pages: 13
MICROENER IM30-CV Operation Manual preview
IM30-CV
Brand: MICROENER Pages: 24
ICS ELECTRONICS VXI-5501 Quick Start Manual preview
VXI-5501
Brand: ICS ELECTRONICS Pages: 4
ZyXEL Communications ZyAIR B-100 Quick Installation Manual preview
ZyAIR B-100
Brand: ZyXEL Communications Pages: 23
Cypress Semiconductor CY8C24223A Specification Sheet preview
CY8C24223A
Brand: Cypress Semiconductor Pages: 31

Brands by name

Popular brands

Load more brands