manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 27 of 760

T bit: The T bit in the status register (SR) is used to indicate the result of compare operations, and
is read as a TRUE/FALSE condition determining if a conditional branch is taken or not. To
improve processing speed, the T bit logic state is modified only by specific operations. An
example of how the T bit may be used in a sequence of operations is shown below.

ADD

#1, R0

;T bit not modified by ADD operation

CMP/EQ

R1, R0

;T bit set to 1 when R0 

=

 0

BT

TRGET

;branch taken to TRGET when T bit = 1 (R0 = 0)

Literals: Byte-length literals are inserted directly into the instruction code as immediate data. To
maintain the 16-bit fixed-length instruction code, word or longword literals are stored in a table in
main memory rather than inserted directly into the instruction code. The memory table is accessed
by the MOV instruction using PC-relative addressing with displacement, as follows:

MOV.W

@(disp, PC), R0

Absolute Addresses: As with word and longword literals, absolute addresses must also be stored
in a table in main memory. The value of the absolute address is transferred to a register and the
operand access is specified by indexed register-indirect addressing, with the absolute address
loaded (like word and longword immediate data) during instruction execution.

16-Bit and 32-Bit Displacements: In the same way, 16-bit and 32-bit displacements also must be
stored in a table in main memory. Exactly like absolute addresses, the displacement value is
transferred to a register and the operand access is specified by indexed register-indirect addressing,
loading the displacement (like word and longword immediate data) during instruction execution.

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Brand: Quantum Pages: 12
Barco ImagePRO-HD Installation Manual preview
ImagePRO-HD
Brand: Barco Pages: 121
Cypress Semiconductor CY62148E Specification Sheet preview
CY62148E
Brand: Cypress Semiconductor Pages: 10
Waves MaxxBCL Manual preview
MaxxBCL
Brand: Waves Pages: 41
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Brand: IDT Pages: 11
Velopex Extra-X Quick Start Manual preview
Extra-X
Brand: Velopex Pages: 7
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Brand: Tandberg Data Pages: 6
ebm-papst R3G175-AF01-02 Operating Instructions Manual preview
R3G175-AF01-02
Brand: ebm-papst Pages: 11
IEI Technology HPE-6S2 Quick Installation Manual preview
HPE-6S2
Brand: IEI Technology Pages: 3
Eneo PNR-5304 Quick Installation Manual preview
PNR-5304
Brand: Eneo Pages: 68
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Brand: Infoblox Pages: 13
CNC4PC C52- ESS User Manual preview
C52- ESS
Brand: CNC4PC Pages: 11
Magma ExpressBox2 EB2 User Manual preview
ExpressBox2 EB2
Brand: Magma Pages: 74
ATI Technologies RADEON 9800 PRO Getting Started Manual preview
RADEON 9800 PRO
Brand: ATI Technologies Pages: 20
Zigen IP-Logic ZIG-IPPRO-RX Quick Start Manual preview
IP-Logic ZIG-IPPRO-RX
Brand: Zigen Pages: 4
Bailey INFI 90 NTAI06 Instruction preview
INFI 90 NTAI06
Brand: Bailey Pages: 33
ZALMAN RESERATOR2 Installation And Operational Manual preview
RESERATOR2
Brand: ZALMAN Pages: 18
Procool SP480 Series Instructions preview
SP480 Series
Brand: Procool Pages: 2

Brands by name

Popular brands

Load more brands