Renesas SH7709S Hardware Manual Download Page 685 | Manualshive

Page: 685 / 807

background image

Rev. 5.00, 09/03, page 641 of 760

Section 22 User Debugging Interface

(UDI)

22.1

Overview

This LSI incorporates a User debugging interface (UDI) and advanced user debugger (AUD) for
program debugging.

22.2

User Debugging Interface (UDI)

The UDI (User debugging interface) performs on-chip debugging which is supported by this LSI.
The UDI described here is a serial interface which is compatible with JTAG (Joint Test Action
Group, IEEE Standard 1149.1 and IEEE Standard Test Access Port and Boundary-Scan
Architecture) specifications.

The UDI in the SH7709S supports a boundary scan mode, and is also used for emulator
connection.

When using an emulator, UDI functions should not be used. Refer to the emulator manual for the
method of connecting the emulator.

22.2.1

Pin Descriptions

TCK: UDI serial data input/output clock pin. Data is serially supplied to the UDI from the data
input pin (TDI), and output from the data output pin (TDO), in synchronization with this clock.

TMS: Mode select input pin. The state of the TAP control circuit is determined by changing this
signal in synchronization with TCK. The protocol complies with the JTAG standard (IEEE Std.
1149.1).

T

TT

TR

R

R

RSSSSTTTT

: UDI reset input pin. Input is accepted asynchronously with respect to TCK, and when low,

the UDI is reset. See section 22.4.2, Reset Configuration, for more information.

TDI: UDI serial data input pin. Data transfer to the UDI is executed by changing this signal in
synchronization with TCK.

TDO: UDI serial data output pin. Data output from the UDI is executed by reading this signal in
synchronization with TCK.

A

A

A

ASSSSEEEEM

M

M

MD

D

D

D0000

: ASE mode select pin. If a low level is input at the

ASEMD0

pin while the

RESETP

pin is asserted, ASE mode is entered; if a high level is input, normal mode is entered. When using
on the user system alone, without an emulator and the UDI, hold this pin at high level. In ASE

«
...
683
684
685
686
687
...
»

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Brand: CAME Pages: 19

grandMA2 Series

Brand: MA lighting Pages: 36

Brand: Teagle Pages: 40

TWR-SB0410-36EVB

Brand: NXP Semiconductors Pages: 26

Brand: C&T Solution Pages: 129

Brand: Patton electronics Pages: 145

Industrial Network Track OSI

Brand: GarrettCom Pages: 10

2410SA - Serial ATA RAID Controller

Brand: Adaptec Pages: 14

Brand: Dave Embedded Systems Pages: 79

Brand: UMAX Technologies Pages: 27

Brand: Avigilon Pages: 12

Macho Rev. A (BW)

Brand: Thermalright Pages: 32

Threat Analysis Reporter TAR

Brand: 8e6 Technologies Pages: 76

Brand: LanReady Pages: 40

Brand: Axtrinet Pages: 49

Brand: Barco Pages: 538

Brand: NetApp Pages: 28

Brand: Extron electronics Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands