manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 383 of 760

11.5

Examples of Use

11.5.1

Example of DMA Transfer between On-Chip IrDA and External Memory

In this example, receive data of the on-chip IrDA is transferred to external memory using DMAC
channel 3. Table 11.8 shows the transfer conditions and register settings. In addition, it is
recommended that the trigger for the number of receive FIFO data bytes in IrDA be set to 1
(RTRG1 = RTRG0 = 0 in SCFCR).

Table 11.8

Transfer Conditions and Register Settings for Transfer between On-Chip SCI
and External Memory

Transfer Conditions

Register

Setting

Transfer source: RDR1 of on-chip IrDA

SAR3

H'0400014A

Transfer destination: External memory

DAR3

H'00400000

Number of transfers: 64

DMATCR3

H'00000040

Transfer source address: Fixed

CHCR3

H'00004B05

Transfer destination address: Incremented

Transfer request source: IrDA (RXI1)

Bus mode: Cycle-steal

Transfer unit: Byte

Interrupt request generated at end of transfer

Channel priority order: 0 > 2 > 3 > 1

DMAOR

H'0101

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

National Instruments NI 9426 Getting Started Manual preview
NI 9426
Brand: National Instruments Pages: 17
mikroElektronika CAN SPI click Quick Start Manual preview
CAN SPI click
Brand: mikroElektronika Pages: 3
Z Microsystems TranzStor 8X User Manual preview
TranzStor 8X
Brand: Z Microsystems Pages: 51
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Brand: Infoblox Pages: 13
Airlink101 AWMB100 User Manual preview
AWMB100
Brand: Airlink101 Pages: 46
Noraxon TeleMyo 2400T V2 User Manual preview
TeleMyo 2400T V2
Brand: Noraxon Pages: 52
BiPOM Electronics CG9103-2RS232-1USB User Manual preview
CG9103-2RS232-1USB
Brand: BiPOM Electronics Pages: 8
Carrier 40VMW005 Installation And Maintenance Instructions Manual preview
40VMW005
Brand: Carrier Pages: 18
Qvis 72-8P Series User Manual preview
72-8P Series
Brand: Qvis Pages: 233
Foxconn RAID Foldout Introduction preview
RAID Foldout
Brand: Foxconn Pages: 1
Axtrinet APG200 User Manual preview
APG200
Brand: Axtrinet Pages: 49
IBA ibaBM-FOX-i-3o-D Manual preview
ibaBM-FOX-i-3o-D
Brand: IBA Pages: 13
Bdcom GP3600-16 Hardware Installation Manual preview
GP3600-16
Brand: Bdcom Pages: 25
HeimVision HM243 User Manual preview
HM243
Brand: HeimVision Pages: 167
Crestron UC-CAM-UPGRD-300 Quick Start preview
UC-CAM-UPGRD-300
Brand: Crestron Pages: 2
Aaeon HSB-668I Manual preview
HSB-668I
Brand: Aaeon Pages: 44
Artesyn Embedded Technology SharpMedia PCIE-8120 Manual preview
SharpMedia PCIE-8120
Brand: Artesyn Embedded Technology Pages: 2
F5 ARX-1500 Manual preview
ARX-1500
Brand: F5 Pages: 12

Brands by name

Popular brands

Load more brands