manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 478 of 760

In transmitting serial data, the SCI operates as follows:

1. The SCI monitors the TDRE bit in SCSSR. When TDRE is cleared to 0 the SCI recognizes

that the transmit data register (SCTDR) contains new data and loads this data from SCTDR
into the transmit shift register (SCTSR).

2. After loading the data from SCTDR into SCTSR, the SCI sets the TDRE bit to 1 and starts

transmitting. If the transmit-data-empty interrupt enable bit (TIE) in SCSCR is set to 1, the SCI
requests a transmit-data-empty interrupt (TXI) at this time.

If clock output mode is selected, the SCI outputs eight synchronous clock pulses. If an external
clock source is selected, the SCI outputs data in synchronization with the input clock. Data is
output from the TxD pin in order from the LSB (bit 0) to the MSB (bit 7).

3. The SCI checks the TDRE bit when it outputs the MSB (bit 7). If TDRE is 0, the SCI loads

data from SCTDR into SCTSR, then begins serial transmission of the next frame. If TDRE is
1, the SCI sets the TEND bit in SCSSR to 1, transmits the MSB, then holds the transmit data
pin (TxD) in the MSB state. If the transmit-end interrupt enable bit (TEIE) in SCSCR is set to
1, a transmit-end interrupt (TEI) is requested at this time.

4. After the end of serial transmission, the SCK pin is held in the high state.

Figure 14.20 shows an example of SCI transmit operation.

Bit 0

Bit 1

Bit 7

Bit 0

Bit 1

Bit 6

Serial clock

Serial data

Transfer direction

Bit 7

TXI interrupt  
handler writes 
data to TDR and 
clears TDRE
bit to 0

1 frame

TDRE

TEND

LSB

MSB

TXI interrupt
request
generated 

TXI interrupt
request
generated 

TEI interrupt
request
generated 

Figure 14.20   Example of SCI Transmit Operation

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Magnat Audio MC 200 Faq preview
MC 200
Brand: Magnat Audio Pages: 2
NEC N8104-128 Installation Manual preview
N8104-128
Brand: NEC Pages: 47
Vonets MINI300 Quick Setting Manual preview
MINI300
Brand: Vonets Pages: 8
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
QNAP TS-1283XU-RP User Manual preview
TS-1283XU-RP
Brand: QNAP Pages: 54
ZALMAN Extreme Gaming VGA Cooler GV1000 User Manual preview
Extreme Gaming VGA Cooler GV1000
Brand: ZALMAN Pages: 7
WAGO 750-459 Manual preview
750-459
Brand: WAGO Pages: 48
Digi ConnectCore 8X Hardware Reference Manual preview
ConnectCore 8X
Brand: Digi Pages: 116
IBM Power System H924 Installing Instructions preview
Power System H924
Brand: IBM Pages: 48
Promise Technology VTrak J310S Quick Start Manual preview
VTrak J310S
Brand: Promise Technology Pages: 26
Intel E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor Datasheet preview
E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor
Brand: Intel Pages: 112
ivideon Bridge B1610 Quick Start Manual preview
Bridge B1610
Brand: ivideon Pages: 11
Alcatel-Lucent 1353 Brochure preview
1353
Brand: Alcatel-Lucent Pages: 12
ADS Technologies API-800 Installation Manual preview
API-800
Brand: ADS Technologies Pages: 21
Air Live AirVideo-100 Quick Setup Manual preview
AirVideo-100
Brand: Air Live Pages: 2
GSA Bolide BN-NVR/NX User Manual preview
Bolide BN-NVR/NX
Brand: GSA Pages: 101
Fast FV3000-W2K Instruction Manual preview
FV3000-W2K
Brand: Fast Pages: 66
Rane CP 52S Operator'S Manual preview
CP 52S
Brand: Rane Pages: 6

Brands by name

Popular brands

Load more brands