manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 653 of 760

22.4.3

UDI Reset

An UDI reset is executed by setting an UDI reset assert command in SDIR.  An UDI reset is of the
same kind as a power-on reset.  An UDI reset is released by inputting an UDI reset negate
command.

UDI reset assert

UDI reset negate

SDIR

Chip internal reset

CPU state

Branch to H'A0000000

Figure 22.3   UDI Reset

22.4.4

UDI Interrupt

The UDI interrupt function generates an interrupt by setting a command from the UDI in the
SDIR. An UDI interrupt is a general exception/interrupt operation, resulting in a branch to an
address based on the VBR value plus offset, and with return by the RTE instruction. This interrupt
request has a fixed priority level of 15.

UDI interrupts are not accepted in sleep mode or standby mode.

22.4.5

Bypass

The JTAG-based bypass mode for the UDI pins can be selected by setting a command from the
UDI in SDIR.

22.4.6

Using  UDI to Recover from Sleep Mode

It is possible to recover from sleep mode by setting a command (0001) from the UDI in SDIR.

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

Yaesu FT-817 - Modification Instructions preview
FT-817 -
Brand: Yaesu Pages: 2
Analog Devices ADAU1961 Manual preview
ADAU1961
Brand: Analog Devices Pages: 76
EVS Neuron NFR2000 Installation And Service Manual preview
Neuron NFR2000
Brand: EVS Pages: 30
SIIG IO1037 Quick Installation Manual preview
IO1037
Brand: SIIG Pages: 6
Lindsay Broadband LBON320AC Series Installation And Operation Manual preview
LBON320AC Series
Brand: Lindsay Broadband Pages: 4
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Brand: Lutron Electronics Pages: 4
NKE BOX Wi-Fi User Manual And Installation Manual preview
BOX Wi-Fi
Brand: NKE Pages: 15
ATI Technologies RADEON 9800 PRO Getting Started Manual preview
RADEON 9800 PRO
Brand: ATI Technologies Pages: 20
Alarm NX-208E Installation Manual preview
NX-208E
Brand: Alarm Pages: 5
Primera Disc Publisher XR Installation Instructions preview
Disc Publisher XR
Brand: Primera Pages: 2
Atmel STK501 Specification Sheet preview
STK501
Brand: Atmel Pages: 2
Intellinet 720564 Instructions preview
720564
Brand: Intellinet Pages: 2
Antec KÜHLER H2O 920 Software Manual preview
KÜHLER H2O 920
Brand: Antec Pages: 6
Knowles IA611 Xplained Pro User Manual preview
IA611 Xplained Pro
Brand: Knowles Pages: 14
Renesas RH850 Series User Manual preview
RH850 Series
Brand: Renesas Pages: 67
Wistron NeWeb DNBA-81 User Manual preview
DNBA-81
Brand: Wistron NeWeb Pages: 32
IBM Nways 2216 Service And Maintenance Manual preview
Nways 2216
Brand: IBM Pages: 168
Vxl IQL Series Hardware Installation Manual preview
IQL Series
Brand: Vxl Pages: 4

Brands by name

Popular brands

Load more brands