manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 319 of 760

10.3.7

Waits between Access Cycles

A problem associated with higher external memory bus operating frequencies is that data buffer
turn-off on completion of a read from a low-speed device may be too slow, causing a collision
with data in the next access. This results in lower reliability or incorrect operation. To avoid this
problem, a data collision prevention feature has been provided. This memorizes the preceding
access area and the kind of read/write. If there is a possibility of a bus collision when the next
access is started, a wait cycle is inserted before the access cycle thus preventing a data collision.
There are two cases in which a wait cycle is inserted: when an access is followed by an access to a
different area, and when a read access is followed by a write access from the SH7709S. When the
SH7709S performs consecutive write cycles, the data transfer direction is fixed (from the
SH7709S to other memory) and there is no problem. With read accesses to the same area, in
principle, data is output from the same data buffer, and wait cycle insertion is not performed. Bits
AnIW1 and AnIW0 (n = 0, 2–6) in WCR1 specify the number of idle cycles to be inserted
between access cycles when a physical space area access is followed by an access to another area,
or when the SH7709S performs a write access after a read access to physical space area n. If there
is originally space between accesses, the number of idle cycles inserted is the specified number of
idle cycles minus the number of empty cycles.

Waits are not inserted between accesses when bus arbitration is performed, since empty cycles are
inserted for arbitration purposes.

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

NEC N8104-213 Installation Manual preview
N8104-213
Brand: NEC Pages: 10
NEC N8104-213 Instructions Manual preview
N8104-213
Brand: NEC Pages: 8
IEI Technology WSB-H610 User Manual preview
WSB-H610
Brand: IEI Technology Pages: 187
IEI Technology TANK-XM811 User Manual preview
TANK-XM811
Brand: IEI Technology Pages: 71
Paradyne 3172 Quick Reference preview
3172
Brand: Paradyne Pages: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Brand: Paradyne Pages: 2
Javad TRIUMPH-3NR User Manual preview
TRIUMPH-3NR
Brand: Javad Pages: 35
National Instruments NI-9252 Calibration Procedure preview
NI-9252
Brand: National Instruments Pages: 9
Amplifier Tech ATP6700 Owner'S Manual preview
ATP6700
Brand: Amplifier Tech Pages: 36
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Brand: Delta Electronics Pages: 1
EVS Neuron NFR2000 Installation And Service Manual preview
Neuron NFR2000
Brand: EVS Pages: 30
SIIG IO1037 Quick Installation Manual preview
IO1037
Brand: SIIG Pages: 6
MFJ MFJ-492 Manual preview
MFJ-492
Brand: MFJ Pages: 11
Acromag APCe7012E-LF User Manual preview
APCe7012E-LF
Brand: Acromag Pages: 23
Top RAMS1000 User Manual preview
RAMS1000
Brand: Top Pages: 21
B+B SmartWorx Airborne M2M ABDN-er-DP55 Series User Manual preview
Airborne M2M ABDN-er-DP55 Series
Brand: B+B SmartWorx Pages: 120
DigiTech RP 3 User Manual preview
RP 3
Brand: DigiTech Pages: 28
Paradyne 8310 MVLt User Manual preview
8310 MVLt
Brand: Paradyne Pages: 108

Brands by name

Popular brands

Load more brands