manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page xxii of xliv

Section 10

   

Bus State Controller (BSC)

......................................................................... 223

10.1

Overview ........................................................................................................................... 223
10.1.1 Features ................................................................................................................ 223
10.1.2 Block Diagram ..................................................................................................... 225
10.1.3 Pin Configuration ................................................................................................. 226
10.1.4 Register Configuration ......................................................................................... 228
10.1.5 Area Overview ..................................................................................................... 229
10.1.6 PCMCIA Support ................................................................................................. 232

10.2

BSC Registers.................................................................................................................... 235
10.2.1 Bus Control Register 1 (BCR1)............................................................................ 235
10.2.2 Bus Control Register 2 (BCR2)............................................................................ 239
10.2.3 Wait State Control Register 1 (WCR1) ................................................................ 240
10.2.4 Wait State Control Register 2 (WCR2) ................................................................ 241
10.2.5 Individual Memory Control Register (MCR) ....................................................... 245
10.2.6 PCMCIA Control Register (PCR) ........................................................................ 248
10.2.7 Synchronous DRAM Mode Register (SDMR)..................................................... 252
10.2.8 Refresh Timer Control/Status Register (RTCSR) ................................................ 253
10.2.9 Refresh Timer Counter (RTCNT) ........................................................................ 255
10.2.10 Refresh Time Constant Register (RTCOR) .......................................................... 256
10.2.11 Refresh Count Register (RFCR)........................................................................... 256
10.2.12 Cautions on Accessing Refresh Control Related Registers .................................. 257
10.2.13 MCS0 Control Register (MCSCR0)..................................................................... 258
10.2.14 MCS1 Control Register (MCSCR1)..................................................................... 259
10.2.15 MCS2 Control Register (MCSCR2)..................................................................... 259
10.2.16 MCS3 Control Register (MCSCR3)..................................................................... 259
10.2.17 MCS4 Control Register (MCSCR4)..................................................................... 259
10.2.18 MCS5 Control Register (MCSCR5)..................................................................... 259
10.2.19 MCS6 Control Register (MCSCR6)..................................................................... 259
10.2.20 MCS7 Control Register (MCSCR7)..................................................................... 259

10.3

BSC Operation .................................................................................................................. 260
10.3.1 Endian/Access Size and Data Alignment ............................................................. 260
10.3.2 Description of Areas............................................................................................. 265
10.3.3 Basic Interface...................................................................................................... 268
10.3.4 Synchronous DRAM Interface ............................................................................. 276
10.3.5 Burst ROM Interface ............................................................................................ 304
10.3.6 PCMCIA Interface ............................................................................................... 307
10.3.7 Waits between Access Cycles .............................................................................. 319
10.3.8 Bus Arbitration ..................................................................................................... 320
10.3.9 Bus Pull-Up .......................................................................................................... 321
10.3.10

MCS[0]

 to 

MCS[7]

 Pin Control ........................................................................... 323

Section 11   Direct Memory Access Controller (DMAC)

.......................................... 327

11.1

Overview ........................................................................................................................... 327

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

D-Link ShareCenter DNS-320L Datasheet preview
ShareCenter DNS-320L
Brand: D-Link Pages: 4
Amperes iPX5500 Instruction Manual preview
iPX5500
Brand: Amperes Pages: 8
Caen A 1735 Technical Information Manual preview
A 1735
Brand: Caen Pages: 14
Wyse C90LE7 Quick Start Manual preview
C90LE7
Brand: Wyse Pages: 8
S&T TPMS1209T02-ER User Manual preview
TPMS1209T02-ER
Brand: S&T Pages: 28
Kontron ePanel-C3 Technical Manual preview
ePanel-C3
Brand: Kontron Pages: 62
Amphenol C2LINX Series Installation Manual preview
C2LINX Series
Brand: Amphenol Pages: 43
Grundfos CIM 060 Installation And Operating Instructions Manual preview
CIM 060
Brand: Grundfos Pages: 40
JOBO Lift CPE-3 Operating Instruction preview
Lift CPE-3
Brand: JOBO Pages: 12
Behringer MU-A043666 Quick Start Manual preview
MU-A043666
Brand: Behringer Pages: 12
Hanwha Vision XRN-3210B4 User Manual preview
XRN-3210B4
Brand: Hanwha Vision Pages: 131
Toshiba Surveillix NVS User Manual preview
Surveillix NVS
Brand: Toshiba Pages: 118
E-line ELI-SIP2-NVR8 User Manual preview
ELI-SIP2-NVR8
Brand: E-line Pages: 231
LDA Audio Tech ZES-22 User Manual preview
ZES-22
Brand: LDA Audio Tech Pages: 16
Myricom Myrinet-2000 Manual preview
Myrinet-2000
Brand: Myricom Pages: 25
Alacritech SEN3001EF Datasheet preview
SEN3001EF
Brand: Alacritech Pages: 2
ASIX SPINET User Manual preview
SPINET
Brand: ASIX Pages: 8
Bodine Quality in Motion 890 Installation Instructions preview
Quality in Motion 890
Brand: Bodine Pages: 2

Brands by name

Popular brands

Load more brands