manualshive.com logo in svg

Renesas SH7709S, Hardware Manual

The Hitachi SH7709S Hardware Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and technical specifications for the SH7709S product. Unlock the full potential of your device by easily accessing this user-friendly manual, ensuring smooth operation and optimal performance.

Share
Download
background image

Rev. 5.00, 09/03, page 636 of 760

21.1.3

I/O Pins

Table 21.1 summarizes the D/A converter’s input and output pins.

Table 21.1

D/A Converter Pins

Pin Name

Abbreviation

I/O

Function

Analog power supply pin

AVcc

Input

Analog power supply

Analog ground pin

AVss

Input

Analog ground and reference voltage

Analog output pin 0

DA0

Output

Analog output, channel 0

Analog output pin 1

DA1

Output

Analog output, channel 1

21.1.4

Register Configuration

Table 21.2 summarizes the D/A converter’s registers.

Table 21.2

D/A Converter Registers

Name

Abbreviation

R/W

Initial Value

Address

*

1

D/A data register 0

DADR0

R/W

H'00

H'040000A0
(H'A40000A0)

*

2

D/A data register 1

DADR1

R/W

H'00

H'040000A2
(H'A40000A2)

*

2

D/A control register

DACR

R/W

H'1F

H'040000A4
(H'A40000A4)

*

2

Notes: These registers are located in area 1 of physical space. Therefore, when the cache is on,

either access these registers from the P2 area of logical space or else make an appropriate
setting using the MMU so that these registers are not cached.

1. Lower 16 bits of the address

2. When address translation by the MMU does not apply, the address in parentheses

should be used.

Summary of Contents for SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7709S

NA DigiNet 416 User Manual preview
DigiNet 416
Brand: NA Pages: 22
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Brand: UNA AUTOMATION Pages: 20
Galaxy Hunter Series Quick Start Manual preview
Hunter Series
Brand: Galaxy Pages: 30
MF DIGITAL 5200 Live Series EventCD Operator'S Manual preview
5200 Live Series EventCD
Brand: MF DIGITAL Pages: 21
Ampro Corporation LITTLE BOARD P5X Hardware User Manual preview
LITTLE BOARD P5X
Brand: Ampro Corporation Pages: 121
Planet IPOE-171-60W User Manual preview
IPOE-171-60W
Brand: Planet Pages: 20
DPS Telecom D-PK-NG432 User Manual preview
D-PK-NG432
Brand: DPS Telecom Pages: 80
EMC VNX5300 Block Hardware Information Manual preview
VNX5300 Block
Brand: EMC Pages: 88
ekwb 3831109819395 Manual preview
3831109819395
Brand: ekwb Pages: 10
Gigamon GigaVUE H TA100-CXP Hardware Installation Manual preview
GigaVUE H TA100-CXP
Brand: Gigamon Pages: 115
TEC Control WiDiCast User Manual preview
WiDiCast
Brand: TEC Control Pages: 4
Ametek Land System 4 Landmark Technic Processor User Manual preview
System 4 Landmark Technic Processor
Brand: Ametek Land Pages: 34
ASTRO U 960 Operating Manual preview
U 960
Brand: ASTRO Pages: 12
Crestron DMC-C Specifications preview
DMC-C
Brand: Crestron Pages: 3
Crestron CAEN-CK-7x1 Quick Start Manual preview
CAEN-CK-7x1
Brand: Crestron Pages: 2
LiveAction LiveWire Quick Start Manual preview
LiveWire
Brand: LiveAction Pages: 2
Dell 100T TR5 Compatibility Matrix preview
100T TR5
Brand: Dell Pages: 90
Aardvark Paylink Lite 2 User Manual preview
Paylink Lite 2
Brand: Aardvark Pages: 12

Brands by name

Popular brands

Load more brands